The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing stress in the rivets, and (3.) the maximum stress at section a-a

Q: The joint is subjected to a force of P = 2-- lb and F = 150 lb. Determine the state of stress at…

A:

Q: An aluminum [E = 10000 ksi] control rod with a circular cross section must not stretch more than…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to…

A: Given is a double shear connection.

Q: Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A: Given data: Load acting , F1 = 15 kips   and F2 = 34 kips Normal stress has to be limited to 17 ksi.…

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A:

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: According to the given dataP=370kNNumber of the bolts is n=5limiting shear stress =190MPaWe need to…

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

A:

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

A: For solution refer below images.

Q: Required information A thick-walled pipe is bent about a horizontal axis by a couple M. The pipe may…

A:

Q: A timber company has designed a series of beams by bonding the top and bottom flanges to the edges…

A: L1=6 inL2=3.1 inL3=8.75 inL4=1.05 in The vertical shear force is V=3800 lbf

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on…

A:

Q: Determine the required thickness of member BC to the nearest 116 in., and the diameter of the pins…

A: Given: The allowable normal stress in member BC, σall = 29 ksi The allowable shear stress in pin,…

Q: 3. Determine the required thickness of member BC and the diameter of the pins at A and B if the…

A: Given: A uniform distributed load of 5 kip/ft applied on member AB. The length of the AB is 10 ft.…

Q: 1. The bars of the pin-connected frame are each 300 x GOo mm in section. Determine the maximum bad P…

A: Given, A truss structure .  Area of the bar , A =300*600 mm = 0.18 m2. Maximum tensile stress ,…

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: A timber company has designed a series of box beams with the geometry shown below. The beams are…

A: Given data  Shear force = 8kN  Find the maximum shear stress and shear stress at joint

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.