n the structure shown, an 8 mm diameter pin is used at A, and 12 mm diameter pins are used at B and D. Knowing that the allowable shearing stress is 120 MPa at all connections and that the allowable normal stress and bearing stress is 240 MPa in each of the two links joining B and D, determine the allowable load P

Q: Three wires are used to suspend the plate shown. Aluminum wires of 18-in. diameter are used at A and…

A: Given data: *The diameter of the wire A and B made up of aluminium is dA=dB=18 inch. *The diameter…

Q: Link AB, of width b =50 mm and thickness t = 6 mm, is used to support the end of a horizontal beam.…

A: Given Width = 50 mm Thickness = 6 mm Allowable normal stress = 2140 MPa Allowable shear shear stress…

Q: Knowing that the allowable stress in section ABD is 80 MPa, determine the largest force P that can…

A:

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: Given data: Applied force, P = 11 kN. Resolve the force P into normal and tangential components. F…

Q: Link AB, of width b = 2 in. and thicknesst = ¼ in., is used to support the end of a horizontal beam.…

A: Handwriting.jpg

Q: A load Pis applied to a steel rod supported as shown by an aluminum plate into which a…

A: given data: for steel rod;diameter(ds)=0.6inthickness of steel rod (ts)=0.4inshearing stress not…

Q: Two plates, eachin. thick, are used to splice a plastic strip as shown. Knowing that the ultimate…

A: P = 325 lbGlued Area (A) ==  2.25 in2

Q: Load P is applied to a steel rod supported as shown by an aluminum plate into which a…

A:

Q: determine the largest load P t

A:

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: The elevation of the platform is controlled by two identical mechanisms, only one of which is shown.…

A: Load = 1500 lb  Here we need to draw free body diagram and solve the sum  So here I am drawing it in…

Q: The frame shown consists of four wooden members, ABC, DEF, BE,and CF. Knowing that each member has a…

A: The free body diagram of the wooden members is as follows: Calculate the moment about the point A…

Q: 20 kN 0.25 m B 0.4 m Each of the four vertical links has an 8 x 36-mm uniform rectangular cross…

A:

Q: Three steel bolts are to be used to attach the steel plate shown to a wooden beam. Knowing that the…

A:

Q: (d) the average bearing stress at C in member BC, (e) the average bearing stress at B in member BC.

A:

Q: Two plates, each 1/8 in. thick, are used to splice a plastic strip as shown. Knowing that the…

A: P = 325 lb τ = 130 psi Glued Area (A) = 58+34x 94- 2 x 12x34x98 =  2.25 in2

Q: The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the…

A: Draw diagram for better understanding of shear stress The plywood splice plates will hold both…

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: he elevation of the platform is controlled by two identical mechanisms, only one of which is shown.…

A: A truss is made up of straight pieces joined together at joints. Through a joint, no member is…

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in,   b=1.6 in normal stress = 18 ksi…

Q: The hub of a flange coupling has a diameter of 135 mm. The flange has a thickness of 20 mm.…

A:

Q: An offset h must be introduced into a solid circular rod of diameter d. Knowing that the maximum…

A: Given data: Maximum eccentric load stress must not exceed 4 times the center load stress, σe = 4σc.…

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine: