The hub of a flange coupling has a diameter of 135 mm. The flange has a thickness of 20 mm. Determine the force that can shear the hub from the flange coupling if the shear stress of the flange is 200 MPa. A. 1 984.2 kN B. 1 343.4 kN C. 1 152.3 kN D. 1 696.5 kN

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

A: Givend=16mmAverage shear stress=260Mpa

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

A:

Q: Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the…

A: Shear stress of magnesium = 45 MPaShear stress of steel = 75 MPaModulus of rigidity magnesium = 18 ×…

Q: Please solve this question in detail. You have to add the free body diagram.

A:

Q: The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress…

A:

Q: me average

A: The tensile force for the mechanishm is .The diameters of the rod are  and .The diameter of the pin…

Q: For the connection shown, the average shear stress in the 18-mm- diameter bolts must be limited to…

A:

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

A:

Q: solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: Given data as per questionLoad on the bar =25 kg=245.25 NLimiting stress of the bar =27.24kpawe know…

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A:

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: GivenP=375N

Q: orce of P₂ = 610 N is exerted on control arm BC, which is securely attached to the solid 39 mm…

A:

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: (a) V =  kN. (b) V =  kN. (c) V =  kN. (d) V =  kN

A:

Q: 81) A wooden member is joined by means of a glue. The allowable stresses are 600 KPa for shear…

A: We have,allowable shear strength for joint, τallow=600kPa=0.6N/mm2allowable tensile strength of…

Q: Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force…

A: Givend=46mmF=24 kNAAB=0.006 m2ABC=0.005 m2AC=y=8.7 mAB=x=10m

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: Given data :- for section AB L = 12 in , d = 0.75 in for section BC L = 15 in , d = 1 in shear…

Q: Two portions of member AB are glued together along a plane forming an angle with the horizontal. The…

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dj =…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16…

A:

Q: 16 kN 125 mm 3. The two boards are joined by plywood splices that are fully glued on the surfaces in…

A:

Q: The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum…

A: Givenn=5d=1inP=10kipst1=34int2=58inw=4in

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A:

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: The ABD rigid bar is connected to the BD rush which consists of a single bar with a width of 25.0 mm…

A:

Q: Knowing that a force of 800N is applied to the indicated pedal, determine the diameter of the pin at…

A:

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

A:

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: For the frame shown, determine the minimum bolt diameter at B if the shear stress in the bolt is…

A:

Q: Handwritten solution with Fbd. No Chatgpt.

A: Step 1:  Step 2:   Step 3:

Q: The lap joint is fastened with four ¾-inch diameter rivets. Ø a. If the allowable shearing stress…

A:

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to 26…

A:

Q: 90 100 mm 100 mm- 10. The average shear stress in each of the 6-mm radius bolts and along each of…

A:

Q: Knowing that the central portion of the link BD has a uniform cross-sectional area of 1350 mm,…

A: To determine the magnitude of force P.

Q: 1.25 ft Determine the maximum allowable weight of passengers on the gondola ride which is suspended…

A: Given, σallowable=18 ksisquare solid steel = 1.5"

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Q: The grain of a wooden member forms an angle of 15° with the vertical. For the state of stress shown,…

A: Given data: Longitudinal stress acting on the wooden member, σx = -4 MPa. Lateral stress acting on…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.