A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load P. The material to be used is a bronze for which E5 14 3 106 psi. Determine the largest load that can be applied, knowing that the normal stress must not exceed 18 ksi and that the decrease in length of the block should be at most 0.12% of its original length

Q: A short column is made by nailing two 1 * 4-in. planks to a 2 * 4-in. timber. Determine the largest…

A: Given Data: The top surface area of center plank (A) is of (2 inchx4 inch) The top surface area of…

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

A: given; diameter (d)=10mmchange in diameter (δd)=2.5*10-3mmelasticity(E)=10.1*104MPapoisson's…

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress,  τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in…

A: Given:Cable diameter = 4mmE =200 GPaMax Stress 190

Q: 4. A load P is applied concentrically to the bar shown. If the allowable normal stress is 76 ksi,…

A:

Q: determine the largest load P t

A:

Q: Two tempered-steel bars, each in. thick, are bonded to a 1/2 -in. mild-steel bar. This composite bar…

A:

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

A:

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Q: 2 m long aluminium rod must not stretch more than 1 mm and the normal stress must not exceed 38 MPa…

A: Givenlength of the rod L=2m=2000mmstrech limit ∆La=1mmnormal allowable stress σa=38MPa=38 N/mm2axial…

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: force p=5000 lbdiameter of Cg section D=0.75 inchto findnormal stress in CG

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.