The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 4 mm, find the maximum load P that can be applied as shown. -B 2.5 m 3.5 m P A 4.0 m C The maximum load P that can be applied is KN.

The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 4 mm, find the maximum load P that can be applied as shown. -B 2.5 m 3.5 m P A 4.0 m C The maximum load P that can be applied is KN.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b. ENGT 2020 -Robotic Fundamentals Lab 3.5 Creating a Program 1. What are the four types of moves and describe how they move between waypoints. a. C.
C- Draw a neat sketch of a SCARA robot and clearly indicate all joints’ variables and types on the drawing?D- How many degrees-of-freedom does a spherical robot have?
I need an answer quickly please.
The following jobs are waiting to be processed at a small machine center: JOB 10 20 30 40 50 DUE DATE 260 254 260 265 275 days (round your response to one decimal place). days (round your response to one decimal place). DURATION (DAYS) 18 T 22 14 32 All dates are specified as manufacturing planning calendar days. Assume that all jobs arrived on day 200 (yesterday) in the order shown but are not scheduled to begin until day 201 (today). a) Sequence the jobs according to LPT. According to the LPT rule, the sequence of jobs should be 50, 20, 10, 30, 40 b) What is the average completion (flow) time? The average completion (flow) time is c) What is the average job lateness? The average job lateness is d) What is the average number of jobs in the system? The average number of jobs in the system is jobs (round your response to one decimal place). 62446
Write down the Part Programming codes for the First alphabet of student (S) in capital Type: Engraving operation
4- Which of the following lines is used to: show the axis of symmetry for feature indicate path of motion part, and show the location for bolt-hole circles and other circular or patterns a) O Folding b) Vision C) Center d) Hidden Boş bırak KOnceki 4/20 Sonraki> Каpat VSinav Bitir
Develop a LabVIEW code of a wire cutting system. Include screenshots.
6. Write one block of code to perform the indicated operation. Assume the location is X2.0, Y2.0, and the depth is Z-1.5 for each operation. 1) Drill with dwell of 0.2 seconds 2) Peck drilling cycle with a 0.15" peck depth 3) Chip breaker with a 0.15" peck and full retract every 0.6" 4) RH tapping cycle for 14-16 NC thread; define a spindle speed and feed 5) Bore a hole with the tool being retracted manually
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
A.) Sketch:[Draw a sketch that represents the situation of the problem, while showing all the variables included in it (vectors or scalars as forces, , displacement, position, etc.).] B.) Approach:[Mention all the laws, principles or concepts, as well as the mathematical equations that solve this problem. Step by step.] C.)Solution:[Develop the physical or mathematical equations used for the solution of the problem and highlight the partial and final answers. Be clear and organized.]
Course: Computer Aided Manufacturing How to describe coding structure of KK-3 codding system?
in autocad typing clip does what?