2. In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/4 in. diameter while a 3/8 in. diameter pin is used at C. Determine: (a) the shearing stress in pin A (b) the shearing stress in pin C (c) the largest normal stress in link ABC (d) the average shearing stress on the bonded surfaces at B (e) the bearing stress in the link at C

Q: 500 N Find the moment 45

A:

Q: 6 - From the question (5) find the real length of the line AB. *

A: the real length of line AB

Q: 200 1s' the Reaction A the Reactions L L Oetermine the value 2. Determine the value 9, the value The…

A:

Q: Replace the two pairs, demonstrated by a single equivalent pair

A: Consider the diagram shown for the given structure,

Q: 12 Find the moment about point O for the given Figure.   a.

A: Option B is correct.

Q: Two forces FA =185 lb and FB =189 lb are acting on the bracket shown with axes x,y,v and w…

A:

Q: The cable of the tower crane is subjected to 840 N force, the magnitude of the moment of the force F…

A: The point A represents the origin of the co-ordinate system.

Q: 1. Determin or false in R³. (a) Two lines parallel to a third line are parallel. (b) Two lines…

A: According to Bartleby guidelines we can answer only one question at a time. Please post other…

Q: I want the methode of counting this two drawing L, and J1 and J2 veryy urgent

A: Full joints are the revolute joint and half joints are the sliding pair.

Q: Free body diagram required. Use paper sheet to solve

A: thank you

Q: 600 mm B 300 mm 200 mm 200 mm 250 mm 40° 30° F=90 N NOT TO SCALE →→> a) [ + → alculate the force F…

A:

Q: 2. the cable at the boom as end of the crane boom exerts a forec OF 279.891b shorn. Express F as a…

A:

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the…

A:

Q: 2. Determine the moment of the four forces acting on the rod as in the fig. about point 'o' 40 N N…

A: The free body diagram for the body is given below,

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: If the diameter (d) of wheel is reduced in half times in size, Then the torque produced in the wheel…

A: If the diameter (d) of wheel is reduced to half times in size, Then the torque produced in the wheel…

Q: peom t (つとやr) 8HF1 DETERMINE THE 3 RE he T IONG FOR THE BENM SHOLIN BOVE.

A:

Q: 3. A rod with a mass of 5kg and a total length of 2 meters that can spin about an axis through its…

A: Write the given data with suitable variables: M=5 kgL=2 mI=ML212F=10 N

Q: Fill in all blanks before submission. Round the answer to the nearest integer. The post shown below…

A: Apply Equilibrium Conditions

Q: The magnitude of the force Q is 569 N. Determine the magnitude of the moment (Nm) of Q about the…

A:

Q: FIGURE Q1 shows a device where a strut is being supported by three cables. It is measured that…

A:

Q: The force F shown below is applied in the positive x-direction against a 20-degree slope. The force…

A:

Q: Find the measure of the angle (in degrees) made by the resultant of the concurrent forces with…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: 3. Determine the angle formed by cable BG and BH,

A: The unit vector from B to G can be determined as,

Q: Co D N B F 500 mm E A 250 mm 300 mm

A: Given,

Q: 200 p 6 10 I 10 K 10 Oetermine the alue the Reachion A 2 Determine the valueg the Reachom L 9, the…

A:

Q: 4. If the resultaut force of tHhe two tug boats required to Io is to be Munimum det the magnitude of…

A:

Q: Q2/compute the moment of force 650 N about the rod AB. 125 mm 150 mm 150 mm 100 m 300man-

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given data: P⊥Pole=760 N Need to determine the component of the force P along line AC.

Q: SOLVE FOR THE MOMENT OF THE 100N FORCE AT POINT A.

A: Consider the below figure: Find the perpendicular distance between the point A and the force:…

Q: EX Find. W and.wat the point.(uv.).(-20).. ne and.Z=u.e.

A:

Q: Q2: Determine (Y). D2 Y Q /sec L (m) D1 D2 220 0.5 5 0.25 D2 Y D1 Hg-

A:

Q: using the Method

A: ∑Fx=088.87+CE+CFsin38.3°=088.87+CE+(-33.6)sin38.3°=0CE=-89.17KN∑Fx=0-CFcos38.3°-CB = 0…

Q: For multiple choice, choose the best answer. Show all work: indicate your plan and draw FBD's (Free…

A: Given data as per question Force =12 N distance =3 m

Q: 0. Determine the magnitude g the Resuftot. b. Determine the Pokce g the Reacionsat A C. Determine…

A: Solution:   The magnitude of the resultant and the support reactions at A and B are calculated…

Q: The truck is being towed by a 450 force. Find the moment about the front tires (point A) due to the…

A:

Q: foce thruugh force through B and comple and a coupl; 6

A: GIVEN DATA - A CANTILEVER TYPE BEAM GIVEN WE HAVE TO REPLACE FORCE WITH FORCE AND COUPLE

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.