A specimen of magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gaugelength of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to:Load(kN)Al(mm)0.0 1.38 2.78 5.63 743 8.14 9.87 12.85 14,10 14.34 13.83 12,590.0 0.03 0.06 0.12 0.20 0.25 0.64 1.913,184.45 5.72 6.99a) Plot the data as engineering stress versus engineering strain.b) Compute the modulus of elasticity.Determine the tensile strength of this alloy.

Given that: For a bar having rectangular cross section, dimension of the cross section is 3.2…

A specimen of magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load (kN) (mm) a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity. Determine the tensile strength of this alloy. 0.0 1.38 2.78 5.63 743 8.14 9,87 12.85 14,10 14.34 13.83 12,59 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99

A specimen of magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load (kN) (mm) a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity. Determine the tensile strength of this alloy. 0.0 1.38 2.78 5.63 743 8.14 9,87 12.85 14,10 14.34 13.83 12,59 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown. Determine the fracture stress. Stress (MPa) 50 40- 30- 20- 10- 0 0 0 Upper scale O 59 MPa O 24 MPa O 40 MPa O 50 MPa O 33 MPa 0.100 0.005 Lower scale 0.200 0.010 Strain (mm/mm) 0.300 0.015 0.400 0.020
5
640 480 160 0.002 0,004 0.006 0.008 0.010 Strain (mm/mm) A tensile test specimen of Aluminum alloy having a gauge length of 280 mm was tested to fracture. Stress and strain data obtained during the test are shown in the attached Figure. **Answers are approximate - do your best to read the graph. Determine: (a) the modulus of elasticity in GPa (4sigs). Enter this value into D2L answer box. (b) the proportional limit in MPa (3sigs). (c) the ultimate strength in MPa (3sigs). (d) Ductility of material based on percent elongation. (3sigs) Your Answer: Stress (MPa)
What value can not be found from the stress-strain graph? Please select one:a. Modulus of elasticityb. Disgracec. Toughnessd. Poisson ratioe. Yield strength
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 450 400 350 300 250 200 150 100 NO 50 0.05 0.1 0.15 0.2 0.25 0.3 0 35 0.4 Strain 300 EN Stress (Mpa)
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
TOPIC: ELASTICITY A load of 50 kg is applied to the lower end of a steel rod 80 cm long and 0.60 cm indiameter. How much will the rod stretch? Y = 190 GPa for steel. Please help me solve this problem with complete solution and box the final answer. Please also draw an illustration based from the given. Thank you!
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Stress-Strain Diagram 1200 1000 800 1000 600 800 600 400 400 200 200 0.005 0.01 0015 0.02 0.025 003 0.1 0.0s 0.15 0.2 025 Strain (mm/mm) Select one: O 0.2% O 19% O 3% 25% O 0.5% Stress (Mpa)
For a steel element with a 0.2% steel characteristic, a stress test was applied and the analysis of the data thrown by the material is required in terms of a variation of force and the respective deformations. Determine the following: A.Determine the percentage elongation at the point where the part develops the fracture. B.Construct the “Stress-Strain” diagram C.Maximum tensile strength of the part.
Made of steel alloy whose engineering tensile curve is given in the figure below, 10 mm diameter and 75 mma tall cylindrical specimen;a) Find the yield strength (0.2% limit).b) Calculate the maximum load it can carry.c) Calculate the elongation that occurs in the length when a load of 20000 N is applied to the sample.
Question 1 The S-N diagram for a titanium alloy is shown in the figure. Calculate the fraction of life consumed by the following sequence of loadings: 15,000 cycles at 80 MPa 120,000 cycles at 60 MPa 3,500,000 cycles at 50 MPa Maximum stress (ksi) 160 140 120 100 80 60 40 20 I 10³ 104 105 Cycles to failure 100 107
need help with this review question Engineering of Materials I got 3,75*10-4 and 6.375*10-4 answers but there incorrect Part B