Q.3. A cylindrical specimen of cold-worked Brass has a tensile strength of 500 MPa. If the specimen remained cylindrical during deformation and its original radius was 10.6 mm, determine its radius after deformation. The dependence of tensile strength on percent cold work is shown in the following Figure.

Q.3. A cylindrical specimen of cold-worked Brass has a tensile strength of 500 MPa. If the specimen remained cylindrical during deformation and its original radius was 10.6 mm, determine its radius after deformation. The dependence of tensile strength on percent cold work is shown in the following Figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

need help...thnks.....
ANSWER Q4 PART B
Help me sir
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm
A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength. Stress (ksi) 60 50- 40- 30- 20 10- 0 0 0 Upper scale O 66 ksi 28 ksi O 72 ksi O 53 ksi O 62 ksi Lower scale. 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.002 0.004 0.006 0.008 0.010 0.012 0.014 Strain (in./in.)
2. A tensile test is performed on a bar of Dural (an aluminium alloy) of diameter 15 mm. The bar yields under a load of 30 kN and reaches a maximum load of 46 kN. Estimate the tensile yield stress and tensile strength of Dural
200 stress 150 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass specimen the diameter is 12-8 mm Calcalate the folluwing:- %3B 1- The Yield stress. 2-Modulus of elasticity. 3 - The Tensile strength.
A wire with circular base of radius 3 mm was subjected to tensile stress of 13.5 N. If half the amount of stress is to be applied to a wire with square base of 1.86 mm width, what must have been the force (in Newton) applied to this new wire?
ELECTRICAL ENGINNERING THANK YOU SO MUCH
A square cross-section v-notched specimen of height 75 mm has each side of 14 mm has been selected to perform Charpy impact test. A v-notch of thickness 1.75 mm is made at the middle of the specimen length. Determine the cross-sectional area at notch. Cross-sectional area at notch (in mm2)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. Initial Cross-sectional Area 2.01 mm2. The Diameter of the Specimen 1.59 mm. Final Length of the Specimen 42.92 mm. Stress at the elastic load 8955.22 N/mm2. Find: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)