A structural member 10 cm long must be able to support a load of 50,000 N without experiencing any plastic deformation. Given the following data for brass, steel, aluminum, and titanium, rank them from least to greatest weight in accordance with these criteria. Yield strength Ultimate tensile Alloy Density (g/cm3) (MPa) strength (MPa) Brass 415 600 8.5 Steel 860 800 7.9 Aluminum 310 435 2.7 Titanium 550 700 4.5

A structural member 10 cm long must be able to support a load of 50,000 N without experiencing any plastic deformation. Given the following data for brass, steel, aluminum, and titanium, rank them from least to greatest weight in accordance with these criteria. Yield strength Ultimate tensile Alloy Density (g/cm3) (MPa) strength (MPa) Brass 415 600 8.5 Steel 860 800 7.9 Aluminum 310 435 2.7 Titanium 550 700 4.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How did temperature affect the toughness of the specimens?
Table Q1 consists of 4 (four) materials with their mechanical properties. The length of a cylindrical rod 380 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load of 24,500 N. (a) Calculate the stress of the cylindrical rod. (b) Compare with data given in Table Q1 which are the likely materials for the cylindrical rod if it does not experience plastic deformation? Justify. (c) What is the likely material if the elongation is less than 0.9 materials? Justify. Table Q1 Modulus of Elasticity, Yield Strength and Tensile Strength Material Modulus of Yield Tensile Strength Strength Elasticity (GPa) (MPa) (MPa) Aluminum 70 255 420 alloy Brass alloy 100 345 420 Copper 110 250 290 Steel alloy 207 450 550
Question 2 Figure 2 shows the dependence of fatigue strength on testing cycles (S-N curve) of an acetal polymer. 60 50 40 30 20 10 104 105 106 107 108 Number of cycles to failure Figure 2 The S-N fatigue curve for an acetal polymer a. What is the fatigue strength, or maximum stress amplitude, at one million cycles of loading? b. An acetal polymer 30-cm-long bar with a diameter of 20 mm is designed to survive one million cycles of loading, what is the maximum allowable axial load that can be applied on one end of the bar? Magnitude of stress Reversal, MPa
A copper specimen of Young's Modulus 122 GPa is subjected to a tensile test in a laboratory and the following data are obtained. a) Initial length of the Specimen = 363 mm; b) Initial diameter of Specimen = 10 mm; c) Yield Stress = 128 N/mm2; d) Ultimate Stress = 212 N/mm2; e) Fracture Stress = 180 N/mm2; %3D g) % of Elongation = 44 %; h) % of Reduction in area = 38 %.
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. FIND: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
short Answer with Explaining all parts of the Question please
(b) A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPa Tensile Strength / MPa Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550
5.3) A cold-worked carbon steel was tested in a tensile test and the results are shown in Table 1 below: Table 1. Tensile test results Original diameter 10,00 mm Final diameter 7,60 mm Original gauge length 102,00 mm Final gauge length 114,30 mm Load at upper yield 31,21 kN Maximum force 36,25 kN Load at fracture 28,65 kN Factor of safety 2 For Questions 5.3.1 to 5.3.8, calculate the following tensile test properties based on the information provided in Table 1 above: 5.3.1) Stress at upper yield. ANSWER TO QUESTION 5.3.1 5.3.2) Ultimate tensile stress. ANSWER TO QUESTION 5.3.2
Content: Stress Analysis. Do you think it is possible for a material to have a high Modulus of Elasticity (at least 70 GPa) whilehaving a high tensile elongation (at least 40%)? Why or why not?
I want to solve the required squares and their units of measurement in regularity, please
Data: Tensile Strength b (mm) L (mm) d (mm) P (N) Tensile Strength (MPa) Average (MPa) 49.74 52.14 10.14 760 49.74 52.14 10.14 980 51.18 49 8.74 800 48.56 48.86 10.96 960 49 51.54 9.72 780
Toughness is a property which relates to (1 Point) Strength Ductility Resilience Ductility and strength