The graph below shows the yield stress for a polycrystalline metal as a function of the grain size of the metal. The point A is (10 microns, 100 MPa) and B is (1000 microns, 28 MPa). Using this data, calculate what is the closest numerical match to the yield stress at 2 microns. yield stress (MPa) 90 8 289 80 70 60 40 30 A 200 Select one: O a. 198.9 MPa O b. 310.9 MPa O c. 252.6 MPa O d. 80.5 MPa O e. 165.2 MPa 400 600 grain size d (microns) 800 B 1000

The graph below shows the yield stress for a polycrystalline metal as a function of the grain size of the metal. The point A is (10 microns, 100 MPa) and B is (1000 microns, 28 MPa). Using this data, calculate what is the closest numerical match to the yield stress at 2 microns. yield stress (MPa) 90 8 289 80 70 60 40 30 A 200 Select one: O a. 198.9 MPa O b. 310.9 MPa O c. 252.6 MPa O d. 80.5 MPa O e. 165.2 MPa 400 600 grain size d (microns) 800 B 1000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer Correctly . Don't Waste my time with Wrong Solution.
Calculate the young’s modulus from one of these two graphs?
Hello, I hope you are fine. I need to do this homework in Metal Engineering. I hope to get your help because I have an important homework.
The creep data have been taken on an ahuminum alloy at 400°C and constant stress of 25MPA are shown in below Table, Find the steady state or minimum creep rate. Time (min) strain Time (min) 16 strain 0.135 0.0 0.0 2 0.025 18 0.153 4 0.043 0.065 20 0.172 0.193 0.218 22 0.078 24 10 0.092 26 0.255 12 0.109 28 0.307 14 0.120 30 0.368
Explain about these graphs and discuss how they are helpful in engineering. (TENSILE TEST)
What is the Young’s modulus in GPa
I need handwritten solution if u skip any part then i swear, it's simple do all otherwise skip
(i) Give the correct number of significant figures for: 4500 0.0032 0.04050 (ii) Write in scientific notation and engineering notation: 0.000467 32000000
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. _x106 lb/in² Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 t 0.00614 Determine the modulus of elasticity for this material: € (in./in.)
Mechanics of material Find core solution for this question. Please ignore the writings in blue the question is typed in black
You have been given the following set of data from a soil-geotextile friction test: Normal stress (kPa) Peak shear strength (kPa) Residual shear strength (kPa) 17 20.2 13 35 31 22 70 52 39.5 140 94 74.5 (a) Plot the Mohr-Coulomb failure envelope (x-axis=normal stress; y-axis=shear stress) (b) Determine the peak friction angle, and the residual friction angle, . (c) Determine the peak adhesion and the residual adhesion. (d) Calculate the fabric efficiency based on a soil friction angle of = 35-degrees using the peak friction angle. **HINT: the equation for efficiency of soil friction angle mobilization is:
Data: Tensile Strength b (mm) L (mm) d (mm) P (N) Tensile Strength (MPa) Average (MPa) 49.74 52.14 10.14 760 49.74 52.14 10.14 980 51.18 49 8.74 800 48.56 48.86 10.96 960 49 51.54 9.72 780