Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Figure σ (ksi) 0 33.2 45.5 49.4 51.5 53.4 € (in./in.) 0 0.0006 0.0010 0.0014 0.0018 0.0022 1 of 1 Part B Determine the modulus of elasticity. E = ksi Submit Part C Determine the modulus of resilience. Ur= in-lb in³ Submit Request Answer Provide Feedback Request Answer

Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Figure σ (ksi) 0 33.2 45.5 49.4 51.5 53.4 € (in./in.) 0 0.0006 0.0010 0.0014 0.0018 0.0022 1 of 1 Part B Determine the modulus of elasticity. E = ksi Submit Part C Determine the modulus of resilience. Ur= in-lb in³ Submit Request Answer Provide Feedback Request Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 450 400 350 300 250 200 150 100 NO 50 0.05 0.1 0.15 0.2 0.25 0.3 0 35 0.4 Strain 300 EN Stress (Mpa)
The strain of a component, which has a tensile modulus of 7 X 105 MPa, and subjected to a stress of 9000KPa, is a. 0.000026 b. 0.000129 c. 0.0026 d. 0.0000129
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. _x106 lb/in² Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 t 0.00614 Determine the modulus of elasticity for this material: € (in./in.)
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Calculate true stress at an engineering strain of 0.04.
A piece of steel rebar is tested in tension to determine its mechanical properties. The length of the sample is 87.3 mm and the cross-sectional area is 52.1 mm². When stretched by 37.2 mm, the force measured is 14,884 N. At this point, the graph is non-linear, but no clear neck is visible. If the Poisson's ratio of the material is 0.281, calculate the cross-sectional area (mm²) at this point.
Load (N) Elongation (mm) In a tensile test of stainless steel, the following data were obtained: 7,200 11,250 13,500 16,200 18,900 20,200 20,700 13,200 24.90 0.0 0.505 2.03 5.08 10.16 15.24 21.80 The dimensions of the cylindrical specimen were initial length L₁= 50.8 mm and initial area A₁ = 35.8 mm² and the area at fracture was Ar = 10.0 mm². Plot the stress-strain diagram and determine the following: a) Modulus of elasticity b) The yield strength at a strain offset of 0.002 c) Ultimate strength d) Fracture strength
A tension test was performed on a specimen having an original diameter of 13.7 mm and a gauge length of 50 mm. The data are listed in the table. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Redraw the linear-elastic region, using the same stress scale but a strain scale of 20 mm = 0.001 mm/mm. From the diagram, determine approximately the modulus of elasticity. Express your answer to three significant figures and include the appropriate units. E = Submit Part B συ = Submit Part C ☐☐ μÅ of = Value Determine the ultimate stress. Express your answer to three significant figures and include the appropriate units. Request Answer μĂ Value Request Answer Units μĂ - Value Units Determine the fracture stress. Express your answer to three significant figures and include the appropriate units. ? Units ? ?
Calculate the young’s Modulus in GPa from the data
A test rod of rust-resistant steel, with a diam. of 12.8 mm and a measuring length of 50.8 mm is subjected to a tensile test. The data from the test is shown in the table below.
You have been given the following set of data from a soil-geotextile friction test: Normal stress (kPa) Peak shear strength (kPa) Residual shear strength (kPa) 17 20.2 13 35 31 22 70 52 39.5 140 94 74.5 (a) Plot the Mohr-Coulomb failure envelope (x-axis=normal stress; y-axis=shear stress) (b) Determine the peak friction angle, and the residual friction angle, . (c) Determine the peak adhesion and the residual adhesion. (d) Calculate the fabric efficiency based on a soil friction angle of = 35-degrees using the peak friction angle. **HINT: the equation for efficiency of soil friction angle mobilization is:
During a tensile test of Aluminum alloy whose initial diameter was 0.505-in and gage length was 2.0-in, the following data was recorded. Load Elongation (in.) Load Elongation (in.) 0.020 (1b) |(Ib) 14 000 2 310 0.00220 14 400 0.025 4 640 0.00440 14 500 0.060 6 950 0.00660 14 600 0.080 9 290 0.00880 14 800 0.100 11 600 0.0110 14 600 0.120 12 600 0.0150 13 600 Fracture a) Determine Stress and strain b) Draw the stress strain diagram c) Determine the following mechanical properties 1) Proportional limit, 2) Modulus of elasticity 3) Yield point 4) Ultimate strength 5) Rupture strength.
The stress-strain diagram for a steel alloy having an original diameter of 0.3 in. and a gage length of 5 in. is shown in the figure below. (Figure 1) Figure σ (ksi) 80 70 60 50 40 30 20 10 0 0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0 0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035 e (in./in.) < 1 of 1 ▼ Part A Determine the modulus of resilience. Express your answer to three significant figures. (ur)approx= Submit Part B (14)approx= Determine the modulus of toughness. Express your answer to three significant figures. Submit ■ AΣ¢ † vec Provide Feedback Request Answer |VL]ΑΣΦΠ = Ivec Request Answer [C] ? MIC ? in-lb in³ in-kip in³