A single lap joint consists of 16 mm thick grade S275 plate as shown in Figure Q1. All edges of the plates are machine flame cut. Two (2) 22 mm diameter Grade 4.6 black non- preloaded bolts and shear plane passes through the unthreaded portion of the bolt. Calculate the design resistance of the connection due to bearing. (CO2-PO5) (C4)

A single lap joint consists of 16 mm thick grade S275 plate as shown in Figure Q1. All edges of the plates are machine flame cut. Two (2) 22 mm diameter Grade 4.6 black non- preloaded bolts and shear plane passes through the unthreaded portion of the bolt. Calculate the design resistance of the connection due to bearing. (CO2-PO5) (C4)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a weld thickness of 7.5mm and that of electrode used is E70. Determine the following: 1. Total Length of weld if P=300KN 2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns P -2-75mmx8mm plates 10mm-thk L1 gusset plate L2 end returns
Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only. L125x100x10 V WT BOTTOM CHORD (please solve completely and neatly thank you so much) 12S
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
4. Is the bearing-type connection shown in the right figure sufficient to resist the 200 k load which passes through the center of gravity of the bolt group? P₁-200 k 3 Eight 7/8-in A325X bolts
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
Using SMAW process, E70 electrodes and an A572 steel. Determine thelength of the side fillet welds for the full capacity the 125x100x10mm angle tensionmember as shown below. Assume that the member is subjected to repeatedstress variations making any connection eccentricity undesirable. Check theblock shear strength of the member. Assume that the WT chord has sufficientstrength to develop the weld strengths and the thickness of its web is 12mm. UseU = 0.87 for class use and LRFD Method only.
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
The connection shown consists of two, grade A307, M16 bolts in standard holes. The bolts are snug-tight and threads are permitted in the shear planes. Deformation around the bolt holes is a design consideration and the bolt spacing is as indicated. The 6.35 mm thick plates material are made of A36 steel. Which of the following most nearly gives the nominal bearing (considering also the tearout) strength of the bolts? CHOICES:a) 192 kNb) 384 kNc) 268 kNd) 195 kN
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
A rolled l-shaped beam is connected to a steel girder by 4-25mm bolts as shown. Determine the maximum end reaction that the beam can resist. (tw=15mm, Fy=248 MPa, Fu=400MPA) 60 mm 25-mm bolts- 3 @ 80 mm W 14 × 211 2 - 100 mm angle leg 60 mm