A rod is made from two segments: AB is steel and BCis brass. It is fixed at its ends and subjected to a torque ofT= 780 N· m. The steel portion has a diameter ofPart A30 mm. The reactions at the walls are the same.Gst = 75 GPa, Gr = 39 GPa. (Figure 1)Determine the absolute maximum shear stress in the shaft.Express your answer to three significant figures and include appropriate units.HA?Figure< 1 of 1(Tmax Jabe = ValueUnitsSubmitRequest Answer< Return to AssignmentProvide FeedbackB1.60 mGy handA0.75 m

Answered: Image /qna-images/answer/c655f413-df5d-438a-a392-ee46c0aa3a34.jpg

A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected to a torque of T= 780 N. m. The steel portion has a diameter of 30 mm. The reactions at the walls are the same. Gst = 75 GPa, Gr = 39 GPa. (Figure 1) Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. ? Figure < 1 of 1 (Tmaa Jabe = Value Units Submit Request Answer

A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected to a torque of T= 780 N. m. The steel portion has a diameter of 30 mm. The reactions at the walls are the same. Gst = 75 GPa, Gr = 39 GPa. (Figure 1) Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. ? Figure < 1 of 1 (Tmaa Jabe = Value Units Submit Request Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
- once answered Correctly will UPVOTE!!
= The L 37 in. long structural member shown below is fabricated with a solid copper core and a stainless steel cover that are bonded together to form a composite shaft. The copper core has diameter Dc = 1.4 in The stainless steel cover has inner diameter (Din)s = 1.4 in. and outer diameter (Dout) ss ss = с = 1.65 in. A torque of T = 104 ft lb is applied at its free end, which is shared between both the copper and stainless steel. Determine the angle of twist of the composite shaft and the maximum shear stresses in the copper core and the stainless steel cover. = -.39 (Tmax) ss = 869.295 (Tmax) c = = 1834.97 L Stainless steel Copper core ? × 0% psi × 0% psi ? × 0%
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
Q) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L), if the stress at the fillet equal to the half stress at the center.
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 30 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B 2 dia of rod 1 = 13mm dia of rod 2 = 11 mm
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
only Handwritten answer needed please. not typed
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal 70 GPa E = 126 GPa E = 200 GPa AAR=58 mm² ABC 77 mm2 Acp = 39 mm² Сopper 20KN 8 kN Aluminum Steel 7 kN B 20KN A 8 kN 450 mm -300 mm -- 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the (6) shaft (3) 2.2. Calculate the displacement of the point C with respect to the fixed-point A 2.3. If the shaft must have one uniform diameter determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not (11) exceed 450 MPa with a factor of safety equal to 1.8.
1. The steel shaft carries the axial loads as shown in the figure below. Determine the change in overall length of the shaft caused by these loads given that P = 3100 Ib. The cross-sectional area for each segment is shown in the figure. Use E = 29 X 10° psi for steel. %3D A = 0.75 in.² ЗР A = 1.0 in.² A = 0.5 in.? 2P -P 4P e-3 ft- - 5 ft 4 ft→