The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 81 mm and an inner diameter of 71 mm. For A-36 steel, Est = 200 GPa, and for 6061-T6 aluminum, Eal = 68.9 GPa. Figure < 1 of 1 > Determine the average normal stress in the aluminum due to this loading. Express your answer to three significant figures and include appropriate units. σal = Submit Part B μА Ost. = Value Request Answer 6 μA Determine the average normal stress in the steel due to this loading. Express your answer to three significant figures and include appropriate units. Value Units Ć ? Units ?

The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 81 mm and an inner diameter of 71 mm. For A-36 steel, Est = 200 GPa, and for 6061-T6 aluminum, Eal = 68.9 GPa. Figure < 1 of 1 > Determine the average normal stress in the aluminum due to this loading. Express your answer to three significant figures and include appropriate units. σal = Submit Part B μА Ost. = Value Request Answer 6 μA Determine the average normal stress in the steel due to this loading. Express your answer to three significant figures and include appropriate units. Value Units Ć ? Units ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable…

A: The maximum allowable shear stress is The outer diameter of pipe is The inner diameter is

Q: plane stress: The point in a material is subjected to the state of generalized UV O=160+. 10 in MPa,…

A: Given:To find:

Q: A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum…

Q: 5. A cylindrical pressure vessel has an inner diameter of 4 ft. If the yield strength for the tank…

Q: Construct a Mohr's circle for the following point stresses: o = 60MPa, oy = 10MPa and Txy = +20MPa,…

Q: At a point in the cross-section of an engineering component an element is subject to the following…

Q: Answer the following

A: Given data The initial temperature of the bar is T1=72°F The final temperature of the bar is T2=0°F…

Q: The state of stress at a point in a member is shown on the element below. If: 0x = 9 MPa Oy=-14 MPa…

Q: Fundamental Problem 8.6 Figure 1 200 mm of 1 400 mm -20 mm A Section a-a F₁ F₂ Part A Determine the…

A: Copyfish OCR Result(Auto-Detect)N/ATranslated(English)N/A -->Redo OCR Recapture…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Need to determine normal stress σn or ( σx ) In the given answer normal stress is shown by σn Data…

Q: A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the…

A: Given: Pressure, P = 40 Mpa Inner diameter, d = 0.3 m Maximum tensile stress, σu = 646 Mpa Factor of…

Q: The bell crank in (Figure 1) is pinned at A and supported by a short link BC. It is subjected to the…

Q: The gas tank shown in Figure 4 is made from A-36 steel and has an inner diameter of 1.50 m The tank…

A: Since you have posted question with multiple subparts so we are solving only first three subparts…

Q: Determine the state of stress at point A on the cross section of the pipe at section a - a. Take P=…

A: Data given P = 6.1 kN ro = 50 mm ri = 40 mm

Q: The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine…

A: Given the following data:Outer diameter of the shaft, do= 4inPower delivered by the engine, P= 190hp…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is
subjected to a tensile force of 200 kN. The pipe has an outer diameter
of 81 mm and an inner diameter of 71 mm. For A-36 steel,
Est = 200 GPa, and for 6061-T6 aluminum, Eal = 68.9 GPa.
Figure
200 KN
400 mm
1 of 1 >
200 KN
Part A
Determine the average normal stress in the aluminum due to this loading.
Express your answer to three significant figures and include appropriate units.
σal =
Submit
Part B
Ost. =
Submit
Value
ЦА
Provide Feedback
Determine the average normal stress in the steel due to this loading.
Express your answer to three significant figures and include appropriate units.
Pearson
Request Answer
Value
←
μLA
Units
Request Answer
?
Units
?
Next >

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

Step 2: Calculations

Step 3: Calculations

Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(3) The cantilever bar as shown on next page is made of a brittle material. At D, Fx-300 lb. F-250 lb, and F-100 lb. Determine the precise location of critical stress element at the cross section at A. Determine the magnitude for each of the stress components considering the stress concentration at A. Find the principal stresses and the maximum shear stress at this location. 2 in 1-in dia. -in R. 12 in
Determine the pricipal stresses and the directions of the principal stresses at points A Refer to Figure P18-50
The tank of the air compressor is subjected to an internal pressure of 0.43 MPa as shown in (Figure 1). The internal diameter of the tank is 550 mm, and the wall thickness is 6 mm. Figure ⁹-1 Y Y Part A Determine the hoop stress acting at point A. Express your answer to three significant figures and include the appropriate units. 0 = Submit Part B 02 = Submit O Provide Feedback HA Value Request Answer Determine the longitudinal stress acting at point A. Express your answer to three significant figures and include the appropriate units. Value HÅ 1 h Units Request Answer Units ? F ?
The state of stress at a point in a component is ox = -14 ksi, oy = -20 ksi, Txy-4 ksi. Sketch the state of stress at the point in x-y and the calculate the principal stresses and the magnitude of the maximum shear stress. OA = ksi OB ksi Magnitide of tmax ksi %D
Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated in the figure.
For the plane stress sigma x = -8MPa, sigma y = 7MPa, tow xy= 6MPa cw, draw a Mohr’s circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the axis to . Draw stress elements
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Epr 100 GPa. Part A If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Value MPа Submit Request Answer Part B If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Figure HA P Obr = Value MPа Submit Request Answer 10 mm Provide Feedback 20 mm P
Suppose that σ = 330 psi and Try = 150 psi in (Figure 1). Figure Part D Specify the orientation of the principal stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. Op₁= Part E OF 0₂ = ΑΣΦΙΚΗ vec Specify the orientation of the maximum in-plane shear stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. 0/ —| ΑΣΦ 11 | vec ? ? o
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. parameter value units L. 450 mm L2 300 mm d₁ 40 mm d2 30 mm P 40 KN L1 d₁ P B CC 030 BY NO SA 2021 Cathy Zupke P L2 D U MPa MPa The stress in AB σAB= The stress in CD and EF: σCD = σEF= E F
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
Steel machine element at the critical section is in biaxial stress state with two principal stress being 300 N/mm2 and 300 N/mm² (equal magnitude). Find the von Mises stress (in N/mm²) in the member