2.A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Findthe number of M48-5 bolts to be used. Material used to produce the bolts is AISI 1044 steelwith maximum tensile stress, o. = 646 MPa. Use a factor of safety =2.M48-5-40 MPa1.0 m->

Given: Pressure, P = 40 Mpa Inner diameter, d = 0.3 m Maximum tensile stress, σu = 646 Mpa Factor of…

Answered: A pressure of 40 MPa shall be contained…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1. P- 10000 Ib 4 in
A steel bolt 8mm diameter fits loosely inside aluminium tube 8mm diameter and 16 mm outside diameter .A nut is fitted onto the bolt and tightened against the tube until the stress in the bolt is 40N/mm^2.calculate the stress in the bolt.If the temperature is now increased by 100 degree celcius .What will be the new value of stress in each components.
A cast ALuminum cylinder o f a portable hdrauli c riveter is 208 mm in ddiameter The pressure. of The luid petermine Sui table thickness is 15,8 NImm2 by gauge. f the Cylinder wall assuming that the ield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial stresses middle radius and at the inner outer surfa ce.
A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside diameter if the ultimate tensile stress is 600MPa and a factor of safety is 5.
None
Bearing stress 2. Please provide proper discussion and illustration also complete solution and clear solution please thank you. Determine the length of a square key to be used for a 3.73 kW 1800 rpm electric motor. Motor shaft diameter is 35 mm and the height of the key is approximately one-half of the shaft size. The bearing stress on the key is?
I need answer within 20 minutes please please with my best wishes
I neeed typing clear
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take oall = 243 ksi for pin material.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the number of M48-5 bolts to be used. Material used to produce the bolts is AISI 1044 steel with maximum tensile stress, o, = 646 MPa. Use a factor of safety =2.