Steel machine element at the critical section is in biaxial stress state with two principal stress being 300N/mm2 and 300 N/mm² (equal magnitude). Find the von Mises stress (in N/mm²) in the member

Given, Principal stresses of equal magnitudes = σ1 = σ2 = 300 N/mm2 Von Mises stress is given by,…

Steel machine element at the critical section is in biaxial stress state with two principal stress being 300 N/mm² and 300 N/mm² (equal magnitude). Find the von Mises stress (in N/mm²) in the member

Steel machine element at the critical section is in biaxial stress state with two principal stress being 300 N/mm² and 300 N/mm² (equal magnitude). Find the von Mises stress (in N/mm²) in the member

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.