A 1.1-in-diameter solid round bar has a groove 0.1-in deep with a 0.1-in radius machined into it. The bar is made of AISI 1020 CD steel and is subjected to a purely reversing torque of 1700 lbf·in. What are the values of the alternating and mean components of the shear stress? The value of the alternating component is kpsi. The value of the mean component is kpsi.

A 1.1-in-diameter solid round bar has a groove 0.1-in deep with a 0.1-in radius machined into it. The bar is made of AISI 1020 CD steel and is subjected to a purely reversing torque of 1700 lbf·in. What are the values of the alternating and mean components of the shear stress? The value of the alternating component is kpsi. The value of the mean component is kpsi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.2P: A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to...

See similar textbooks

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
Section A: General A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength of 250 MPa. The component has an external diameter of 45 mm and a wall thickness of 3 mm. It has a length of 4 m. A1. The component is subject to a torque of 580 Nm. Calculate the Shear Stress at the external surface A2. The component then has a tensile load applied normal to its cross-section of 38KN. Calculate the resulting longitudinal stress.
100 kip 10 kip -ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? O01 = 31.8 ksi 02 = 76.4 ksi O 01 = 94.0 ksi 02=-62.1 ksi O 01 = 14.3 ksi %3D 02 = -6.37 ksi O o1 = 7.96 ksi !! 02 = 9.55 ksi
the Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel are (allow)mg = 45MPa and (allow)st=84 MPa, respectively. the shear modulus of elasticity for Am1004-T61 magnesium alloy is 18 GPa and for A-36 steel is 75 GPa determine the maximum allowable torque that can be applied to A (see attached jpg file) find the corresponding angle of twist of end A
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
2. The diameters of the solid shafts are: AB is 0.6 in, A B D BC is 0.75 in. and CD is 0.9 in. The applied torques are: TĄ = 400 in lb, Tg = 1200 in Ib, Tc = 500 in İb. Determine the maximum shear stress in each of the three shafts. TA TB Ans: TmaxAB = 9431 psi, TmarBC = 9658 psi, TmaxCD = 9082 psi Te Fixed to wall
8. A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1 = 100 N m, T: = T4 = 50 N m, and T3 = Ts = 80 N m. The tube has an outside diameter of d2 _ 25 mm. The allowable shear stress is 80 MPa and the allowable rate of twistis 6_/m. Determine the maximum permissible inside diameter di of the tube. Ans: [ di = 20.7mm ] T = 100N.m T2 = 50N.m T = 80N.m T4 - 50N.m Ts- 80N.m в D E 25mm
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A 2.5-in.-diameter solid aluminum post is subjected to a horizontal force of V = 4.70 kips, a vertical force of P = 7.35 kips, and a concentrated torque of T = 12.05 kip-in., acting in the directions shown. Assume L = 3.5 in. Determine the normal stress σy at point H.