The steel shaft is made from two segments AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G-10.8 (10¹) ksi. (Egure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. 195.ΑΣΦ. 41 | voc TRAX Submit Request Answer Provide Feedback ? ksi

The steel shaft is made from two segments AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G-10.8 (10¹) ksi. (Egure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. 195.ΑΣΦ. 41 | voc TRAX Submit Request Answer Provide Feedback ? ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: To determine the shear stress in the following shaft at points A and B. The material is steel.…

Q: 1000 Nom 1060Nom TITTITIIT

Q: For the steel shaft shown in Fig. Determine the maximum torque transmitted by any transverse cross…

A: For better understanding Draw the schematic diagram of the above problem.

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

Q: I only need 5

A: Solution:

Q: A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected…

Q: The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A…

Q: A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at…

Q: The torque of 250 kN.m produces a maximum shear stress of 48 MPa in the 8 m-long hollow steel shaft.…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Q: 40-mm-diameter The steel shaft is subjected to the torques shown. Determine the angle of twist of…

A: To Find : The angle of twist of the end. Given : The young modulus is G=75 GPa. Free Body Diagram :

Q: The 70-mm-diameter solid shaft shown is subjected to torques of 600 N·m and 1400 N·m at points B and…

Q: The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage…

A: Given Data: The torque subjected to the fuselage is, T=8 MN·m=8 MN·m×1000 mmm=8×103 MN·mm. The…

Q: The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C…

Q: In the image below, B and C are pulleys. The belts on the pulleys exert the forces shown in the…

Q: The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine…

A: Given the following data:Outer diameter of the shaft, do= 4inPower delivered by the engine, P= 190hp…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The steel shaft is made from two segments: AC has a
diameter of 0.5 in, and CB has a diameter of 1 in The
shaft is fixed at its ends A and B and subjected to a torque
of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1)
Figure
0.5 in.
8 in.
D 500 lb-ft
12 in.
1 of 1
1 in.
B
Determine the maximum shear stress in the shaft.
Express your answer in kilopounds per square inch to three significant figures.
Tmax
Submit
Provide Feedback
IVE ΑΣΦ. 11 | vec
Request Answer
?
ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of torque in section

VIEW

Step 3: Calculation of maximum shear stress

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 13 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as shown in Figure Q2. Knowing that the entire shaft is made of aluminium for which G=27GPa, a. Determine the maximum shear stress and its location. Angle of twist at end D. b. EMU2113 Ø40 Ø30 Section p-p р A р 200 Section q-q 016 1500 Nm q 200 All dimensions in mm Figure Q2 Section r-r 500 Ø30 D 500 Nm
A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m. Determine the resulting torque maximum and minimum shear stress.
A hollow aluminum shaft with an outside diameter of 76 mm and a wall thickness of 5 mm has an allowable shear stress of 49 MPa. Determine the maximum torque T that may be applied to the shaft. O 2.47 kN-m O 1.94 kN-m O 2.11 kN-m O 1.33 kN-m O 1.82 kN-m
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tlow = 35 MPa and (Pacallow =2°, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L,, L,, and D. L1 L2 A 3T 2T Student L, D L, (m) ID (m) (mm) 1131731 0.6 78
The compound shaft is composed of bronze cylindrical segment AB and steel cylindrical segment BC. The two ends of the compound shaft are fixed to rigid supports. The external torque (T') is applied at B. The shear modulus of segment AB and BC is 40 GPa and 80 GPa, respectively. The length of the segment AB and BC is 2 m and 1 m, respectively. The diameter of the segment AB and BC is 0.05 m and 0.025 m, respectively. Determine the external torque T applied to point B so that one of the principal stresses for a point H on the surface of the segment AB is – 100 MPa. T H. B C A 2 m 1 m
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of T = 9060 Ib-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. O 3.31 ksi O 5.15 ksi O 4.05 ksi 3.82 ksi O 2.53 ksi