The rod shown below is made of two different materials. Segment AB is made of aluminum (G=3.9x106 psi). Segment BC is bonded to segment AB and is made of brass (G-5.6×106 psi). Segment BC is hollow and has an inner diameter of di = 0.8 in. External torques are applied to the rod at point B and point C. Let LA = 53.0 in, LB = 42.0 in, dA = 3.8 in, dB = 2.5 in, TB = 7.0 kip?in, and TC= 18.0 kip?in.

The rod shown below is made of two different materials. Segment AB is made of aluminum (G=3.9x106 psi). Segment BC is bonded to segment AB and is made of brass (G-5.6×106 psi). Segment BC is hollow and has an inner diameter of di = 0.8 in. External torques are applied to the rod at point B and point C. Let LA = 53.0 in, LB = 42.0 in, dA = 3.8 in, dB = 2.5 in, TB = 7.0 kip?in, and TC= 18.0 kip?in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected to a torque of T= 780 N· m. The steel portion has a diameter of Part A 30 mm. The reactions at the walls are the same. Gst = 75 GPa, Gr = 39 GPa. (Figure 1) Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. HA ? Figure < 1 of 1 (Tmax Jabe = Value Units Submit Request Answer < Return to Assignment Provide Feedback B 1.60 m Gy hand A 0.75 m
Problem 3. A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar is R = 50 mm and the outside radius is o = 4C mm. Find the maximum allowable radial interference 3 if the assembly is to have a safety factor of 2 against yielding. Both parts are made of carbon steel having E 200 GPa and Sy = 300MPa Solve using the DET. ↑ O
The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor of safety is 2 Spindle length 1 m Size the shaft as the outer diameter / inner diameter ratio is 1.5 Note:show the calculations in detail
5. The steel propeller shaft ABCD carries the axial load shown in Fig. ESS4-SP-027. Determine the change in length of the shaft caused by these loads. Use E = 200 GPa for steel. Rigid 40° C B 4 m 10,000 N Fig. ESS4-SP-027
Please solve
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 > ▾ Part A Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. dc = Submit μA Value Provide Feedback Request Answer Units ? 4
A torsional moment T = 8,019 Nm and a load P = 39,980 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q8. The load P is applied in the centre of the shaft's circular cross-sectional area. The shaft has an inner diameter d = 38 mm and an outer diameter D = 90 mm. Point A in Figure Q8 is on the outer surface of the shaft. Figure 8 Calculate the maximum principal stress at point A. Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.
TEST YOUR UNDERSTANDING! Problem 1 Four wires support the rigid members CD and AB. If a 500-lb load is applied at point I, determine the angle of tilt of AB and the displacement of point A. The members were originally horizontal, each wire has a cross-sectional area of 0.5 in² and E = 29 x 106 psi. (Taken from Hibbeler, 2015) Follow these questions for your solution: 1. Draw the FBDs of bar CD and bar AB. What are the forces in the wires? Problem 2 The horizontal rigid bar is supported by bars A and B and a pin support. If the system is loaded by P₁ and P2, what would be the vertical displacement of the point of application of P₁? Follow these questions for your solution: 1) Draw the FBDs needed. What is the normal force in bar A? in bar B? 2) Draw the deformation diagram. What compatibility equation would you use to determine the displacement of the point of application of P₁? How did the horizontal bar tilt? Answer to Test your understanding box 1 Problem 1: E Problem 2: D THA 1.8 ft…
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal 70 GPa E = 126 GPa E = 200 GPa AAR=58 mm² ABC 77 mm2 Acp = 39 mm² Сopper 20KN 8 kN Aluminum Steel 7 kN B 20KN A 8 kN 450 mm -300 mm -- 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the (6) shaft (3) 2.2. Calculate the displacement of the point C with respect to the fixed-point A 2.3. If the shaft must have one uniform diameter determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not (11) exceed 450 MPa with a factor of safety equal to 1.8.
We have an assembly with a steel rod AB and an aluminum BC, each having a cross sectional area shown in Figure 2. If the assembly is subjected to axial loadings at point A and B shown in Figure 1, Determine the displacement of rod BC and the deformation of rod AB. The original length of each rod is shown in Figure 1. Show manual integration for area under the parabola must be shown E. = 200 GPa. Ed = 70 GPa
A cylindrical rod of diameter 10 mm and length 1.0 m is fixed at one end. The other end is twisted by an angle of 10o by applying a torque. If the maximum shear strain in the rod is p×10-3 , then what is the value of p?