Question 6AB112 mm1.2 m0.9 mFigure 6The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD ismade of A992 steel:a. Find the vertical and horizontal component acting on the pin of the pulley C.b. Find the compressive force in the rod BD.c. Find the effective length-factor for BD.d. Express the radius of gyration about any centroidal axis for a solid circular area as afunction of the diameter of a circle.e.Find the critical effective slender ratio (KL/r), according to the AISC specifications.f.Determine the required minimum diameter of the A992 steel solid circular rod BD tothe nearest mm as allowed by the AISC specifications.g. Determine the F.S. for buckling of the designed rod DB.-0.9 mP

Answered: Image /qna-images/answer/fef8ab61-b873-4b7e-b6d4-f6fb1e287e30.jpg

The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of A992 steel: a. Find the vertical and horizontal component acting on the pin of the pulley C. b. Find the compressive force in the rod BD. c. Find the effective length-factor for BD.

The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of A992 steel: a. Find the vertical and horizontal component acting on the pin of the pulley C. b. Find the compressive force in the rod BD. c. Find the effective length-factor for BD.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Shown below is a picture of a Go-Kart which weighs 300# (with the rider), distributed with 60% of…

Q: Calculate the minor axis (z-z) axial flexural buckling capacity of a 152×152×30UC S275 assuming an…

A: Whenever underlying individuals are exposed to compressive powers , the individuals might fall…

Q: For the suspended load F-310lb of the figure. Calculate the magnitude of the ball-and-socket…

Q: Problem Statement Based on Problem 5-40 from the textbook. Determine the stiffness k of each spring…

Q: 7. In the wedge shown in the figure. Determine the largest angle that will cause the wedge to be…

A: As per given question We have to determine the largest angle

Q: Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each…

Q: 200 GPa young's modulus of a piston rod of diameter 20 mm and length 700 mm in a hydraulic cylinder…

A: Given:Young's modulus, E=200 GPaDiameter, d=20 mmlength, l=700 mmcompressive force, F=10 kN

Q: 1. Find the load in members AD and AE for the truss shown in the figure. Use last three digits of…

Q: Bar ADB is supported by a cable and a pin and is subjected to a distributed load and a couple…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: 2. Link BE and cable CF are attached to a pin on one end and a rigid bar ABCD at the other end. Both…

Q: -4. Determine the load in member CH of the truss shown in Figure P5-4. 6 kips 15 kips

Q: The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the…

Q: Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal…

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as shown below

Q: Solve the problem

A: Step 1: Step 2: Step 3: Step 4:

Q: Problem Statement Based on Problem 5-40 from the textbook. Determine the stiffness k of each spring…

A: Given: Here is the given data, Bar's rotation, θ=15° Force, F=15 N a=1.0 mb=1.8 m To find: The…

Q: Determine the z, y, z components of the moment of reaction at B using scalar notation. Expr

Q: Draw a free body diagram of part AD and part DCB. Show all detail. The compound is supported by a…

Q: Determine the force in member JH and BH for the truss loaded and supported as shown in figure (3).…

Q: A pin in a knuckle joint carrying a tensile load F deflects somewhat on account of this loading,…

A: Answer Explanation:Step 1: Step 2: Step 3: Step 4:

Q: For problem on the picture. assume that the left side of the spring has a fixed end and the other…

Q: Determine the force in member JH and BH for the truss loaded and supported as shown in figure (3).…

A: Consider the left part of the section of the beam as shown below.

Q: 0.4 m 0.2 m y 0.3 m 0.6 m HF .5 m EFG kirişinin enine kesiti B 0.25 m 1200 N Q2) As shown in the…

A: Given: The weight carried by structure, W = 1200 N The width of the cross-section, b = 25 mm The…

Q: Find the force in member HI

Q: The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a…

Q: Compute the design factor in the middle portion only of the rod AC if the steady vertical force on…

Q: The 1.5 kN vertical OA pole is supported as shown in the figure and loaded with a horizontal force…

A: Given: The weight of the pole is 1.5 kN. The pole with the supported load is shown below:

Q: 8. The following assembly is supported by a pin at A and frictionless a roller at B in the given…

Q: D F 4m E 3m 3m he pin-jointed frame work in the figure If a vertical concentrated load of 800KN…

Q: Draw a Free-Body Diagram of the bars AD and BC shown in the figure. Assume all hinges to be smooth…

Q: An aluminum ring has an outside diameter of 12.0 mm and an inside diameter of 10 mm. If the ring is…

A: Given data as per question Outside diameter = 12.0 mm Inside diameter = 10 mm

Q: From the given truss, find the force of member AH, Load 1 = 178 kN, Load 2 = 399 kN Solve this using…

Q: Find the axial force in member BE (units of kips). (Make sure to include a negative sign if it is in…

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A: Given:H=335 lbJ=211 lbFind:The internal resultant normal force in member CD

Q: An A-992 steel wire is connected at ends B and C With an initial diameter of 15 mm. The weight of…

Q: -1m 1m Ql: A: Draw a Free-Body Diagram of the bars AD and BC shown in the figure. Assume all hinges…

Q: Design the yoke and rod connection as shown on the figure to withstand a load of 14 KN. If the…

Q: Based on Problem 5-40 from the textbook. Determine the stiffness k of each spring so that the…

Q: In the figure below, the load that the pin at point O can safely carry is 5 kN. In this case, find…

Q: Find the normal efforts for truss bars illustrated (draw and compression). Consider loads in kN and…

Q: Assume that all members are pin connected and P= 5 kN. (Eigure 1) Figure n Part A Determine the…

Q: An aluminum tube of length 0.01R (m) is used as column (fixed at both ends) carrying an axial load…

A: Given data:-Length, L=0.01R=0.01×993=9.93mAxial load, P=1.333R=1.333×993=1323.669NOuter diameter of…

Q: Consider the frame shown in (Figure 1). Suppose that F₁ = 26 kN. Part A Determine the x and y…

Q: Find the Axial Forces in members 1 - 5. Find the Displacement Displacement of joint A (mm, positive…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find Force in member BD of the truss shown in Figure 1. State whether it is in tension or compression
A pin in a knuckle joint carrying a tensile load Fdeflects somewhat on account of this loading, making the distribution of reaction and load as shown in part (b) of the figure. A common simplification is to assume uniform load distributions, as shown in part (c). To further simplify, designers may consider replacing the distributed loads with point loads, such as in the two models shown in parts (d) and (e). Given: a = = 0.9 in, b= 1.5 in, d= 0.9 in, and F= 3240 Ibf. (c) a+b a+b (d) (a) (e) Estimate the maximum bending stress and the maximum shear stress due to V for the three simplified models. The maximum bending stress for the model (c) is kpsi. The maximum shear stress for the model (c) is kpsi. The maximum bending stress for the model (d) is kpsi. The maximum shear stress for the model (d) is kpsi. The maximum bending stress for the model (e) is kpsi. The maximum shear stress for the model (e is! knsi
Solve the components of force at B along ABC beam
Show the complete solution
The figure shows the combined design of an angular contact ball bearing on two fulcrums. The radial loads R1 and R2 and axial load Fa of bearings 1 and 2 are shown in the figure. The relationship between the derived axial force S and radial load R is: S = 0.25R. Calculate the actual axial force of bearing 1 and bearing 2? Fa= 360N R1=4000N R2=4250N Problem 5) Figure
If F=1kN,the magnitude of the vertical reaction force developed at the point B?
5
How we draw the freebody Diagram for B ( and how we relove it with angle 60 dgree ) ???
The system shown is composed of an ABG bar, supported by a pin at point A and by a collar smooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and the Rod BDE is supported by a pin at D and a cable at end E. Calculate the load P, such that the cable force EF is 20lb.
Needs Complete typed solution with 100 % accuracy.
i need the answer quickly