Beam OC is suspended on rods 1, 2, 3 made of a material with Young's modulus E. The rods have cross-sectional areas F1, F2 and F3 respectively; the length of the rods is a. The distance from the joint and between the rods is also a. The beam is considered a rigid body compared to the rods. The left end of the beam is attached to a rigid wall at point O with a hinged connection. At point C, it is loaded with force P. The weight of the beam is neglected compared to the force P. P 14 kN, F1=F2=F3=F. Determine the value of axial force Ni in rod 1. Give the answer in (kN), rounded to an integer. F1 F2 F3 1 B C P 1.

Beam OC is suspended on rods 1, 2, 3 made of a material with Young's modulus E. The rods have cross-sectional areas F1, F2 and F3 respectively; the length of the rods is a. The distance from the joint and between the rods is also a. The beam is considered a rigid body compared to the rods. The left end of the beam is attached to a rigid wall at point O with a hinged connection. At point C, it is loaded with force P. The weight of the beam is neglected compared to the force P. P 14 kN, F1=F2=F3=F. Determine the value of axial force Ni in rod 1. Give the answer in (kN), rounded to an integer. F1 F2 F3 1 B C P 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. What is the direction of the edge formed between the intersection of (211) and (102)?
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your answer should have 0 decimal places needed. Ex: 76,440 10 - 30 B
many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is 7'-3" long and 4'-2" wide? 7. There are 15 risers in a set of stairs running from the basement to the first floor. Each riser is 7 1/4" high. What is the distance between floors? 8. The distance between two floors is 9'-0 1/2". If 14 risers are to be used in a set of stairs, what is the height of each riser?
If this were to be written how would it look like?
IS. 03 16. The shaft, as shown in Fig. 14.20, is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 3.5. B. TA2 A D. TA 150 -100- TB2 100 All dimensions in mm. Fig. 14.20 The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile stress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion and bending factors as 1.25 and 1.75 respectively, find the shaft diameter. Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare the weights of the two shafts. Ans. 30 mm : 24 mm: 1.82]
Q1 Figure Q1 shows a gear system. Find(i) The relationship between the number of the gear teeth N1 & N2 and the radius r1& r2(ii) The distance travelled along the surface of each gear(iii) The work done of each gear
I didn't understand how you find the angle Alpha = 21.63
3. Determine the displacement of an eight-cylinder engine having a bore of 3.25 in and a stroke of 3 in.
Gear A has 12 teeth and a diameter of 2". Gear B has 6 teeth and a diameter of 1 ". How many rotations will Gear B make when Gear A completes one full rotation?
Determine the distance from the x-axis to the center of the hole in inches.