A shaft is made of an aluminum alloy having an allowable shear stress ofTallow = 116 MPa. (Figure 1) The diameter of the shaft is 115 mm.FigureT< 1 of 1Part ADetermine the maximum torque T that can be transmitted.Express your answer to three significant figures and include appropriate units.SubmitPart BT= 20.516kN•mYou have already submitted this answer. Enter a new answer.No credit lost. Try again.μASubmitAT' 28.4 kN-mPrevious Answers Request AnswerWhat would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft?Express your answer to three significant figures and include appropriate units.Provide Feedback?Previous Answers✓ CorrectCorrect answer is shown. Your answer 28.336 kN-m was either rounded differently or used a different number of significant figures than required for this part.-XP Pearson

Answered: Image /qna-images/answer/29f151dd-57cd-4e11-b3d2-476f1ed034db.jpg

A shaft is made of an aluminum alloy having an allowable shear stress of Tallow=116 MPa. (Figure 1) The diameter of the shaft is 115 mm. Figure 1 of 1 ▾ Part A Determine the maximum torque T that can be transmitted. Express your answer to three significant figures and include appropriate units. Submit Part B T= 20.516 kN m You have already submitted this answer. Enter a new answer. No credit lost. Try again. S T' 28.4 kN-m = Submit · Previous Answers Request Answer What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft? Express your answer to three significant figures and include appropriate units. Provide Feedback ? Previous Answers ✓ Correct Correct answer is shown. Your answer 28.336 kN-m was either rounded differently or used a different number of significant figures than required for this part. P Pearson

A shaft is made of an aluminum alloy having an allowable shear stress of Tallow=116 MPa. (Figure 1) The diameter of the shaft is 115 mm. Figure 1 of 1 ▾ Part A Determine the maximum torque T that can be transmitted. Express your answer to three significant figures and include appropriate units. Submit Part B T= 20.516 kN m You have already submitted this answer. Enter a new answer. No credit lost. Try again. S T' 28.4 kN-m = Submit · Previous Answers Request Answer What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft? Express your answer to three significant figures and include appropriate units. Provide Feedback ? Previous Answers ✓ Correct Correct answer is shown. Your answer 28.336 kN-m was either rounded differently or used a different number of significant figures than required for this part. P Pearson

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

! Required information A steel shaft is to be designed so that it is supported by roller bearings. The basic geometry is shown here, with L = 325 mm, a = 32.5 mm, and F= 3400 N. To achieve a reasonable bearing life, the allowable slope at the bearings is 0.0025 mm/mm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. With the diameter known, what is the maximum deflection of the shaft? The maximum deflection of the shaft (ymax) is - mm.
Question 1) The stepped shaft shown in the figure is rotating at 1000 rpm while transmitting power from a turbine to a generator. The safety coefficient of the steel determined in the design is 50 MPa. a) Determine the maximum power that can be transmitted for the preliminary design shown.b) If the radius of the round part is increased to r = 24 mm in the final design, what will be the percentage change in the power that can be transmitted according to the first design
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
Part A A shaft is made of an aluminum alloy having an allowable shear stress of Tallow = 104 MPa. (Figure 1) The diameter of the shaft is 115 mm. Determine the maximum torque T that can be transmitted. Express your answer to three significant figures and include appropriate units. HA T = Value Units Submit Request Answer Part B Figure 1 of 1 What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft? Express your answer to three significant figures and include appropriate units. .T µA ? T' = Value Units
A solid 1.9 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 520 rpm? What is the maximum shear stress developed in the shaft? Part 1 Convert the given shaft speed to units of rad/s. Answer: W= i rad/s
2. A 1020 CD steel shaft (Sy=390 MPa) is used to transmit 20 kW of power at 1200 rpm. There are no bending or axial loads on the shaft. It is desired to have a static factor of safety of 2 based on the Distortion Energy theory. Determine the minimum diameter needed for the shaft. Power, P= To Pure torsion, relationship between T and t Torsional stress
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s2, the value of y for carbon steel to be 76.5 x 103 N-m-3, and the value of Eto be 207 x 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. If the goal is to double the critical speed, what is the new diameter in mm? (You must provide an answer before moving to the next part.) The new diameter is mm.