Problem 5.37 The 6-hp reducer motor can turn at 1200 rev/min. The allowable shear stress for the shaft is Tallow = 6 ksi. Part A Determine the smallest diameter of the shaft to the nearest 1/16 in. that can be used. Express your answer to four significant figures and include appropriate units. d=32215 in Submit My Answers Give Up Incorrect; Try Again ? Provide Feedback Continue

Q: Cad drawing and assembly drawing of a trolley jack

A: A trolley jack, also known as a floor jack or hydraulic jack, is a mechanical device used to lift…

Q: How many auxiliary views are found on this print?

A: Some objects are too complex that do not show the best geometry of the part by three principle view.…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…