The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The design requires that the end D of the shaft CD doesn't rotate more than 4°, and both shafts shall have the same diameter. Determine the required diameter of the shafts.

The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The design requires that the end D of the shaft CD doesn't rotate more than 4°, and both shafts shall have the same diameter. Determine the required diameter of the shafts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: To determine the shear stress in the following shaft at points A and B. The material is steel.…

Q: 150 B D C St Al 50 30 300 N.m 600 500

A: Applied torque, T=300 N-m Diameter of the aluminum section, dAl=50 mm Diameter of the steel section,…

Q: Design the smallest diameter of the solid shaft if its rotation is to produce 600 HP at 15…

Q: A 45-mm-diameter solid steel shaft supports loads PA-1.2 kN and Pc-2.7 kN as shown. Assume that L₁ -…

A: The diameter of the solid shaft d =45 mmThe support loadThe length of the sectionAt point B is…

Q: A steel propeller for a windmill transmits 8.1 kW at 63.4 rpm. If the allowable shear stress in the…

A: To find : The minimum diameter required for a solid shaft . Given : The power is P=8.1KW The speed…

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…

A: for solution refer below images.

Q: A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of…

Q: Problem 4 A solid circular drive shaft connect a motor to gears B and C. The torque on gear B is 600…

A: Torque on gear B = 600 Nm Torque on gear C = 200 NmG = 66 GPa = 66 × 109 PaDiameter d=25 mmRadius r…

Q: A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the…

A: Given Data: Allowable shear stress ζallow=12 ksi Diameter of shaft=d=1.5 in Radius of shaft…

Q: allowable shear stress in the shafts is 60 MPa. Determine the maximum power that can be transmitted…

Q: A motor supplies 154 hp at 470 rpm to flange A of the shaft. Gear B transfers 74 hp of power to…

Q: The stainless-steel shaft shown below is solid with a diameter of 120 mm. The shaft is fixed at A…

A: Given:DIameter, d=120 mmTB=500 N.mTC=800 N.mG=75 GPa

Q: ches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable…

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A: Given data: The diameter of the part AB is dAB=15 mm The diameter of the part BC is dBC=18 mm The…

Q: A mild steel shaft transmits 18 kW at 450 r.p.m. It carries a central load of 900 N and is simply…

A: Maximum tensile or compressive stress=56 MPa

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

Q: A mild steel shaft transmits P is 18 kW at N is 525 r.p.m. It carries a central load of 900 N and is…

Q: 3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe…

Q: The driveshaft of an automobile is being designed to transmit 131 hp at 2960 rpm. Determine the…

A: To Find : The minimum diameter required for the solid steel shaft. Given : The allowable shear…

Q: If T = 600 Nm, determine the absolute maximum shear stress in the shaft (in MPa) b. If the maximum…

Q: The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in…

Q: 4.) A 12 watts DC motor is used to run a remote-controlled car. A 3-inch aluminum shaft, with a…

A: Answer: (a) The maximum shear stress in the shaft is 3.65 MPa. (b) The angle of twist at the free…

Q: The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm.…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: 4- A hollow tubular shaft is 1.5 m long and has an outer diameter of 75-mm. The shaft transmits the…

Q: The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the…

A: Given Data The diameter of the shaft is: d=8×10-3 m The length of the shaft is: L=200×10-3 m The…

Q: The driveshaft of an automobile is being designed to transmit 197 hp at 3810 rpm. Determine the…

A: GivenP=197hpN=3810rpmσ=5600psi

Q: A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the…

Q: A circular composite shaft is made of a 50-mm-diameter brass (G = 40 GPA) and a 80-mm-outside…

A: Brass dimeter =d2=50-mm with G2 = 40 GPa Aluminum diameter=d1=80mm with G1= 25 GPa L=1.5 m T=100N.m…

Q: Consider the maximum allowable shear stress in the shaft. Calculate the minimum diameter required…

A: Given data: From the previous part, ◆ The maximum allowable shear stress in the steel: τs,allow =…

Q: The driveshaft of an automobile is being designed to transmit 242 hp at 2980 rpm. Determine the…

Q: 3. Find the diameter of a solid steel shaft to transmit 27 kW at 300 r.p.m. The ultimate shear…

A: Given:-Power, P=27 kWSpeed, N=300 rpmUltimate shear stress, τu=360 MPaFactor of safety, FOS=8Ratio…

Q: The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the…

A: Write the given data with suitable variables. G=11×103 ksi=11×106 psiPM=3 hpN=1800 rpmζallow=9…

Q: A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa…

Q: The steel shaft is made from two segments AC has a diameter of 0.5 in, and CB has a diameter of 1 in…

A: The diameter of the AC section is .The diameter of the CB section is .The modulus of rigidity is

Q: 2. The maximum torsional moment a solid shaft can bear is T = 0.2n kN m. If the allowable shear…

A: According to the information we have a torque of 0.2 π kN and allowable shear stress is t =50 Mpa…

Q: A solid circular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP…

Q: A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

4. The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The
design requires that the end D of the shaft CD doesn't rotate more than 4°, and both
shafts shall have the same diameter. Determine the required diameter of the shafts.
40 mm
T = 1000 N - m
D
100 mm
400 mm
600 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A steel shaft (G = 80 GPa) with an external drive of 30mm must transmit a torque of 2700 N-m. The allowable shear stress in torsion is 120 MPa and the allowable rotation for the member is 0.1 rad / m. Design to the nearest millimeter the internal radius required for the steel drive
A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same length and the same outside diameter. It is required to design the steel shaft to withstand double the shear stress that of aluminum shaft. Determine the inside diameter of the stee I shaft. Find the values of the shear stresses on each shaft if a torque of 3 kN.m is applied to both of d=20mm them.
Please give proper and step by step solution. solid circular shaft is subjected to a bending moment of 300 kNm, a twisting moment of 125 kNm. If the yield stress of the shaft material is 350 N/mm², determine the diameter of the shaft according to the maximum shearing stress theory of failure.
Detailed solution would be appreciated thanks!!. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70092104 Pa and angle of twist of 2.25ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.43 m, and y = 1.89 m. Round off the final answer to two decimal places.
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
A shaft drives a gear set that is transmitting 5 hp at 1750 rpm. The diameter of the shaft is 0.75 in. Determine the torsional shear stress developed in the shaft.
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1