تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy = Sy (Neglect buckling) 600 kN 8 m 100 mm T 600 kN

تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy = Sy (Neglect buckling) 600 kN 8 m 100 mm T 600 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A shaft made of mild-steel up at 300 rpm. The supported langth of the weighing It carries pullays each. at distance of Im a of Assuming safe valua the diameter of the shaft. P: 100 kw W: 1500 N S. stress: 60 MPa. = 300 rpm is required to transmit 100 kw shaft 3m. is 1500 N supported from the ands respectively. stress as 60 MPa, determine P= 1500N P. 1500 N B -> RB two pullays A RA 3m
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in, is subjected to an axial force of P-850 lb, a horizontal force of Pz 1560 lb, and a concentrated torque of T-2940 lb-in, acting in the directions shown. Assume a 49 in. Section propertles for the pipe are A-2.2514 in.?,J-8.199 in.", and ly 1-4.0995 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element Answer: Oy = psi Txy psi
It's a mechanics of material, please help me
EHide blocks Lets consider a solid circuiar shalt subjected to the torque loads as shown. Determine the minimum required diameter "Dif the shaft is made of a material having a shear modulus G 50 GPa, so that the maximum angle of twist at its end will not exceed -0.35° (calculated according to the positive sign convention). 100 N.m 500 N.m 200 N.m 300 mm 600 mm 600 mm Select one: O 40 mm O 70 mm O 80 mm O 60 mm O 50 mm
Please I need an answer within half an hour
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
i need the answer quickly
Part A The A 30 stoel boit is tightened within ia hole so that the reactive torque on the shank ABcan bo exprotsed by the equation f (kz)N m/m, whem zn meters A torque of T-50N mis ppled to the bol heed Assume the shank has a constant radius of 6 mm The shear modulus tf elasticity for A.36 sleel is 15 GPa (En.1) Determine the constant k Express your answer using three significant figures. V A veo Submit Renunst Answer Figure Part B Deteemne the amount of twrst in me 50 nm ength or me snan Express your answer using three significant figures Va AL vec Tad Submit Besuest AnswE Activate Windows Pearson
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Need correctly, in proper handwritten solution. Correct ans will be surely upvoted
Q1 The screw of the shaft straightener exerts a load of 3000Kg. The screw-type is square threaded of outside diameter (7.5cm) and (6mm) pitch. Take the height of the nut (150mm). Determine 1) Force required at the rim of 30cm diameter hand wheel, assuming a coefficient of friction is 0.12. 2) The maximum compressive stress in the screw, bearing pressure on the thread, and shearing stress in the thread. 3) Efficiency of the straightener. Nut T 150 ↓ Hand wheel Screw 100 150- 400 All dimensions in mm