A compound bar consists of a steel and bronze segment (Gs t= 80 GPa and Gbr = 40 GPa), The limiting shear stress in steel and bronze are 160 MPa and 60 MPa respectively, and the rotation at B is limited to 0.05 rad. Determine the maximum allowable torque in kN-m if the diameter is 1/10 of a meter.

A compound bar consists of a steel and bronze segment (Gs t= 80 GPa and Gbr = 40 GPa), The limiting shear stress in steel and bronze are 160 MPa and 60 MPa respectively, and the rotation at B is limited to 0.05 rad. Determine the maximum allowable torque in kN-m if the diameter is 1/10 of a meter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show complete process and FBD
A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa 25° A B Wheel
The compound shaft is composed of bronze cylindrical segment AB and steel cylindrical segment BC. The two ends of the compound shaft are fixed to rigid supports. The external torque (T') is applied at B. The shear modulus of segment AB and BC is 40 GPa and 80 GPa, respectively. The length of the segment AB and BC is 2 m and 1 m, respectively. The diameter of the segment AB and BC is 0.05 m and 0.025 m, respectively. Determine the external torque T applied to point B so that one of the principal stresses for a point H on the surface of the segment AB is – 100 MPa. T H. B C A 2 m 1 m
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
Parvinbhai
A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed atend A as shown in Figure 1. The brass sleeve and steel shaft have a modulus rigidity Gb= 40 GPa and Gs = x0 GPa. The length of the assembly is L = 400 mm. The outerdiameters of the shaft and sleeve are d1 = 70 mm and d2 = 90 mm, respectively. Giventhe shear stress of brass is τb = 70 MPa and shear stress of steel is τs = 110 MPa.[Note: x value - Use the last non-zero digit from your group number. If the group numberis zero, use the second last digit instead. For example, if your group number is 5, your xvalue is 5 and Gs = 50 GPa; if your group number is 10, your x value is 1 and Gs = 10GPa.] In this situation, Group number is 2. 1) Write the equations of equilibrium for AB and BC section of the shaft in terms of Twith the help of free body diagrams. 2) Determine the polar moment of inertia for brass sleeve and steel shaft.
Determine the resisting torque at support A and B , of the shaft shown in the figure.
Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel and aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist more than 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa, Ga 28 Gpa. Aluminium Steel 75 .mm 100 mm 1m
Read the question carefully and give me all right solutions. Internal torque at rod 1 (kip-ft) Magnitude of shear at rod 2 & 3(ksi) Rotation angle at rod 1 (deg) Rotation angle at flange C (deg)
The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in. 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. Tmax Submit Provide Feedback IVE ΑΣΦ. 11 | vec Request Answer ? ksi
1. Rod ABCD is made from two materials with two cross sectional areas. The rod is subjected to axial loads as shown. Neglect the weight of the rod and determine the displacement of point A. EBE Ep =210 Gla 125 kN EAg = 70 GR ABE Aco=900 u AAB = 450 mm 37stEN/ %3D 2m 2.5m