A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is subjected to a torsional moment if the copper supports 1.5 times the torque supported by the material of the circular bar. Find the relationship between the outer and inner diameters of the copper tube which has a young's modulus of 4x10^3 Kg/mm2 and the modulus of rigidity is 8x10^3 Kg/mm2

A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is subjected to a torsional moment if the copper supports 1.5 times the torque supported by the material of the circular bar. Find the relationship between the outer and inner diameters of the copper tube which has a young's modulus of 4x10^3 Kg/mm2 and the modulus of rigidity is 8x10^3 Kg/mm2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Related questions

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

Q: A 12 mm thick steel tire has a width of 110 mm has an internal diameter of 800 mm. Tire is heated…

A: Answer: (a) The tensile stress in the tire is 125 MPa. (b) The compressive pressure between the tire…

Q: A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter…

A: GIVEN DATA DIAMETER D=1.2m =1200mm HOOP STRESS =100MPa E=200KN/mm2 α=6.5*10-6/'C We have to find…

Q: Find the length of a flat spiral spring 25 mm wide by 0.5 mm thick to store 8 N.m of energy for a…

A: For a limiting stress of 800 MPa, we need to determine the length of a flat spiral spring 25 mm wide…

Q: . A thin plate is composed of four CST elements, as shown inthe figure below. The plate is subjected…

A: I have attached the image below Explanation:

Q: An open coiled heilcal spring made of 6 mm diam- eter steel wire and 60 mm mean coil diameter, with…

A: We know that an axial torque T is applied to an open coiled helical spring formed of 6 mm diameter…

Q: A simply supported circular steel plate of diameter 1 m and thickness 50 mm is subject to an…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: A thin cylinder 75mm internal diameter, 250 mm long with wall 2.5mm thick is subjected to an…

A: The objective of the question is to determine the change in internal diameter and length of a thin…

Q: A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and…

Q: The rod shown below is made of two different materials. Segment AB is made of aluminum (G=3.9x106…

Q: A cylindrical steel pressure vessel has a 700 mm inner radius and 15 mm thick walls. Find the change…

Q: An elastic rubber sphere of radius 20mm is pressed upon a rigid sphere of radius 50mm. The Young’s…

Q: A hollow circular shaft of inner radius 10 mm outer radius 20 mm and length 1 m is to be used as a…

A: Given Data⇒ Hollow circular shaft Inner radius (r)=10 mm Outer radius (R)=20 mm Length (L)=1 m shear…

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: The L-shaped arm ABC shown in the Fig.3 lies in a vertical plane and pivots about a horizontal pin…

Q: A steel circular tube is subjected to torsion by torques T applied the ends as shown below. The bar…

Q: The copper pipe (G= 50 GPa) is tightly secured to the wall at A, has an outer diameter of 40 mm and…

A: The objective of the question is to determine the maximum shear stress developed in the copper pipe…

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: Let's considera rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: A circular tube of aluminum is subjected to torsion by torques T applied at both end. The bar 0.5m…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A: In possion's ratio always consider change in diameter without concerning the sign only take…

Q: Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: determine the applied force F.

Q: A composite spring has two closed coiled springs connected in series, each spring has 12 coils at a…

Q: Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is…

A: Introduction: A thin cylindrical shell is also known as a pressure vessel, and these vessels are…

Q: A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid…

Q: Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of…

Q: 2) A bar of length 5 m is subjected to an axial tensile load of 100 KN. The bar is 25 mm diameter…

A: According to the given information we have a bar of 5 m to an axial load of 100 Kn the bar is 25 mm…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Find the relationship between the outer and inner diameters of the copper tube which has a young's modulus of 4x10^3 Kg/mm2 and the modulus of rigidity is 8x10^3 Kg/mm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid steel bar with a diameter of 30 mm. A support at one end of the bar and a hard plate at the other end of the tube hold them both tightly in place. A torque T = 650 Nm acting on the end plate twists the composite bar, which has a height of 850 mm. Assuming that the steel's shear modulus is G = 80 GPa, find the maximum shear stresses in the bar and tube, respectively, and the angle of rotation (in degrees) of the end plate
Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is subjected to an internal pressure of 7 MN/m²; the increase in volume due to the pressure is 2.36 x 106 m³. Find the values of Poisson's ratio and the modulus of rigidity. If, in addition to the internal pressure, the cylinder is subjected to a torque of 190 N.m, and axial tensile force at the ends of 650 N, determine the magnitude of the principal stresses set up in the cylinder and their directions. Assume the Elasticity modulus, E = 210 GN/m².
A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The bar is 1.5m long, and the inside and outside diameters are 30mm and 50mm, respectively. It is determined by measurement that the angle of twist is 2.53° when the torque is 4800Nm. Calculate the shear modulus of elasticity “G”.
A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and 3inches long in the z direction. The block is subjected to triaxial loading of three uniformly distributed forces as follows: 50kips tension in the x direction, 65kips compression in the y direction, and 55kips tension in the z direction. If v=0.30 and E=29x10^6 psi. What is the total elongation in the x-direction? a. 6.208 x 10^-4 in b. 1.09 x 10^-3 in c. 1.11 x 10^-4 in d. 6.88 x 10^-4 in What is the total elongation in the y-direction? a. 6.208 x 10^-4 in b. 1.11 x 10^-4 in c. 6.88 x 10^-4 in d. 1.09 x 10^-3 in What is the total elongation in the z-direction? a. 1.11 x 10^-4 in b. 6.208 x 10^-4 in c. 6.88 x 10^-4 in d. 1.09 x 10^-3 in Single Uniformly Distributed Load in the x-direction that would produce the same deformation in the z-direction as the original loading a. 130 kips (T) b. 120 kips (C) c. 120 kips (T) d. 130 kips (C) -Draw and label the diagram correctly, No diagram in…
. A thin plate is composed of four CST elements, as shown inthe figure below. The plate is subjected to a uniform tensile traction sacting on the right edge and a concentrated force F at the center. Usethe following values: E = 105 GPa, ν = 0.3, t = 5 mm, L = 400 mm,H = 400 mm, s = 50 MPa, and F = 150 kN.(a) Compute all the nodal displacements.(b) For each element, compute the element stress components σxx, σyy,and τxy.(c) For each element, compute the element planar principal normal stressesσ1′ and σ2′.(d) For each element, compute the Von Mises and Tresca effective stresses. Please help solve using only FEM( Finite Element Method) and the values given, very urgent. Thank you.
2. A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter of the tire if after shrinking on, the hoop stress in the tire is 100 MPa. Assume E=200kN/mm2. Also find the least temperature to which the tire must be heated above that of the wheel before it could be slipped on. The coefficient of linear expansion for the tire is 6.5×10–6 per °C.
A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The bar is 1.5m long, and the inside and outside diameters are 30mm and 50mm, respectively. It is determined by measurement that the angle of twist is 2.53° when the torque is 4800Nm. Calculate the maximum shear stress in the tube. O 1.5m 3pmm 50mm O <