Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5.

Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
i need the answer quickly
A workshop crane is lifting a load of 28 kN through a wire rope and a hook. The weight of the hook etc is 15 kN. The rope drum diameter may be taken as 30 times the diameter of the rope. The load is to be lifted with an acceleration of 1.2 m/sec2. Take a factor of safety of 6 and Young's modulus for the wire rope is 80 kN/mm2. The ultimate stress may be taken as 1800 MPa. The cross-sectional area of the rope may be taken as 0.38 times the square of the wire rope diameter. Neglect the effect of impact load. Calculate the diameter of the wire rope.
I need the answer as soon as possible
Find the tension of the cord that extends from point C to D and compute for stress experienced by the catble if it's diameter in 1.51 in? Neglect the members weight and friction Round-off your answer into the nearest whole number 150 Ib/ft 6 ft 8 ft 6 fh -12 ft
estion 11 62.5 mm Кey 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P = 256 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.
Need in 1hour pls, thanks The technician is exerting a force of 200N to adjust the shaft at A as shown with the use of a key that has a dimension of d and 25mm. The shaft is fixed. Compute for the d if the 35 MPa maximum shear stress is required for the key.
The thick walled cylinder of a hydraulic system is acted by a hydraulic pressure of 370 psi while themaximum load of the piston is 5500 lbs. If the allowable tensile stress is 2 ksi, find the required wallthickness of the cylinder.
The motor in the figure is transmits movement to the flywheel. The power of the engine is 4 kW and its speed is 525 rpm. 60 mm as per supplied Find the stress on the diameter shaft. dimensions in mm
i need the answer quickly
The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of 221 MPa.