The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn steel. The shaft was turned on a lathe using standard carbide tooling. No heat treatment of the shaft was performed. Assume 99% reliability based on material property data. Shaft dimensions are shown in the illustration below. All dimensions in mm. External force is 3.927 KN. Calculate the highest alternating stress in the shaft, in MPa.

The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn steel. The shaft was turned on a lathe using standard carbide tooling. No heat treatment of the shaft was performed. Assume 99% reliability based on material property data. Shaft dimensions are shown in the illustration below. All dimensions in mm. External force is 3.927 KN. Calculate the highest alternating stress in the shaft, in MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A Drive Shaft for a milling machine transmits 30 horsepower at a speed of 500 RPM. Compute the…

A: A Drive Shaft for a milling machine transmits P = 30 horsepower = 30 × 746 Watts, at a speed of N =…

Q: An SAE 1040 Cold Drawn Steel shaft is subjected to a Torque of 1,200 lb-ft. If the design factor N=2…

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: Given that, AISI 1040 steelDiameter of shaft, D=30 mm,Torque applied on shaft, T=40 N.mBending load…

Q: The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb. Rapid cycling…

Q: material is AISI 1040CD steel. The reliability of the design is 90%. The r/d for the shoulder is…

Q: The critical speed of the shaft is 847.5 rad/s.

A: Given datathe diameter of the steel rod d = 24 mm = 0.024 mthe length of the steel rod l = 600 mm =…

Q: Problem 4: A cast iron shaft, ASTM-25 with an ultimate tensile strength of 25,000 psi, is subjected…

Q: A drive shaft is made of a hollow tube with an outer diameter of Do 2.5 in. It is desired to…

Q: A solid 1040 hot-rolled steel shaft 42 in long has a rectangular cross section of 2.5 in x 3.6 in.…

Q: Required information A steel tube with a circular cross section has an outside diameter of 310 mm…

A: Steel tube with a circular cross section outside diameter D= 310 mm t= 2mm. length, L= 2 m torque,…

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

A: Given data: Shaft is made of AISI 1040CD steel Shaft rotation N=1600 rpm Applied force F1=1600 lbf…

Q: A 25-mm-diameter shaft is statically torqued to 230 N. m. It is made of cast 195-T6 aluminum, with a…

A: T= 230 N-m; yield strength in tension =160 MPa ,yield strength in tension =160 MPa ; yield strength…

Q: What factor of safety is needed for a 2 in. diameter shaft with an ultimate strength of 50,000 psi…

A: diameter of shaft, d=2 in.ultimate strength= 50000 psiTorque transmitted= 40000 in.lbThe objective…

Q: Given a 10 mm diameter steel bar with Su = 1200 MPa and Sy = 950 MPa, with a machined surface,…

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: A cantilevered round shaft with shoulder filet is to be used for application that involves cyclic…

A: Given, Number of cycle, N=500,000 cyclesReliablity, R=99.9999 %Type of shaft: AISI 1018 hot rolled…

Q: A stepped shaft has dimensions of D = 2 in., d = 1 in., and r = 0.1 in. It is machined from AISI…

A: given data :D=1.2 inchd=1 inchr=0.03inso=100ksiSY=80ksiassumption the shaft is manufactureis as…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 18 mm…

A: Part A) The outer diameter of the tube is do = 24 mm = 0.024 mThe inner diameter of the tube is di =…

Q: Required information A solid 1040 hot-rolled steel shaft 41 in long has a rectangular cross section…

A: Given data: L=40 ina=3 .6 inb=2.5 inT=30 kip.in Need to determine the maximum torsional shear stress…

Q: The applied torque on shaft CD is T' = 95 N·m. The journal bearings B, C, and D allow free rotation…

Q: ne section of the shaft shown in the figure is to be designed to approx dr=D/20 with diameter d…

A: To given that,d=0.75Dr=D20Sut=175kpsiSy=160kpsiHB≥370As we know…

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: A 25-mm-diameter shaft is statically torqued to 230 N · m. It is made of cast 195-T6 aluminum, with…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Free-body diagram

VIEW

Step 2: Calculation of highest alternating stress

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

35.15 abs 9.81 was also wrong reposting this again Pls do thumbs up will be given
! Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The shaft is loaded with a transverse load of 13 kN as shown in the figure. The shaft is made from AISI 1060 hot-rolled steel. The surface has been machined. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 mm 50 mm 25 mm 13 kN R1 R2 Not to scale. Determine the minimum fatigue factor of safety based on achieving infinite life.
Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces appliedto this shaft is given below. What would be length of the shaft considering the conditions as givenbelow;− 40 Nm torque is applied throughout the shaft (torque)− 100 kg load is applied at the end point of the shaft (bending)− 250 kg load is applied to push the shaft in the compression direction (normal force)− Factor of safety should be 2
Like will be given :)
Let FA=100 N and FC= 208.33 N for the shaft below. The shaft is made of 2014 aluminum alloy with yield strength of 276 MPa. a) Based on the von Mises theory (use design safety factor of 4), select the shaft's cross-sectional dimension. What is the realized factor of safety? b) Based on the maximum shear stress (MSS) theory (use design safety factor of 4), select the shaft's cross-sectional dimension. What is the realized factor of safety?
Compute the torsional shear stress and the angle of twist in degrees in an aluminum tube, 600 mm long, having an inside diameter of 60 mm and ar outside diameter of 80 mm when subjected to steady torque of 4500 N m. Then specify a suitabl aluminum alloy for the tube. 51.
Please full steps. Big clear Handwriting. Thanks
Homework help
1. The steel shaft shown below has a hardness of 150 Bhn and experiences completely reversed torsion, T. The surface is machined, and a reliability of 50% is required. If a 1.5 safety factor is desired, calculate the reversed torque, T, to guarantee that the part will not fail under fatigue. 24 mm 2 mm rad. 0.8 mm rad. 20 mm 24 mm 150 Bhn
2. At a machined shaft shoulder the small diameter d is 25mm the large diameter D is 40mm, and the fillet radius is 2.5 The bending moment is 2300N mm and the steady torsion moment is 1800 N mm The heat-treated steel shaft has an ultimate strength of Sut- 850Mpa The reliability goal is 099 (ka- 0.786, kb 0.870, ke 0.814) Determine the fatigue factor of safety of the design described in this section
SHOW COMPLETE AND CLEAN SOLUTION and DRAW ILLUSTRATION
I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals. I’m expecting a range between 100-280 ft-lbs but can justify it.