2. COMPUTE THE: A. PROPORTIONAL LIMIT B. MODULUS OF ELASTICIT Y C. YIELD STRESS AT 0.2 % OFFSET D. ULTIMATE STRESS E. NOMINAL RUPTURE STRESS Use a scale of 1cm = 25MPa and 1cm=0.025mm/mm. For Last name starts from A-L, the load given in the table is added by 1.0kN except for Load OkN. For Last Name, starts from M-Z, the load given in the table is added by 2.5kN. Elongations do not change. A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. Using the data listed in the table, plot the stress-strain diagram. Load (kN) Elongation (mm) 0 0 11.1 0.0175 31.9 0.0600 37.8 0.1020 40.9 0.1650 43.6 0.2490 53.4 1.0160 62.3 3.0480 64.5 6.3500 62.3 8.8900 58.8 11.9380

2. COMPUTE THE: A. PROPORTIONAL LIMIT B. MODULUS OF ELASTICIT Y C. YIELD STRESS AT 0.2 % OFFSET D. ULTIMATE STRESS E. NOMINAL RUPTURE STRESS Use a scale of 1cm = 25MPa and 1cm=0.025mm/mm. For Last name starts from A-L, the load given in the table is added by 1.0kN except for Load OkN. For Last Name, starts from M-Z, the load given in the table is added by 2.5kN. Elongations do not change. A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. Using the data listed in the table, plot the stress-strain diagram. Load (kN) Elongation (mm) 0 0 11.1 0.0175 31.9 0.0600 37.8 0.1020 40.9 0.1650 43.6 0.2490 53.4 1.0160 62.3 3.0480 64.5 6.3500 62.3 8.8900 58.8 11.9380

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Cad drawing and assembly drawing of a trolley jack

A: A trolley jack, also known as a floor jack or hydraulic jack, is a mechanical device used to lift…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: Scale board

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given:

Q: What is the maximum thickness dimension allowed on the part?

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

Q: The explantion is not clear

A: given : height of channel h = 10m width of channel w= 34m angle made by channel θ= 15o to find:…

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: draw the top , left , front view?

Q: Okay I did everything you did but the only thing I didn't do was take away 10 degrees from my…

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

Q: Question 2 ( When creating a solid model part intricate geometry of your part, s True

A: Solidworks or ansys is a software where simpler and more complex designs can be drawn with each…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: What is the sliding block?

A: To Define: Sliding block

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

SHOW COMPLETE AND CLEAN SOLUTION and DRAW ILLUSTRATION

2. COMPUTE THE:
A. PROPORTIONAL LIMIT
B. MODULUS
OF
ELASTICIT
Y
C. YIELD STRESS AT 0.2%
OFFSET
D. ULTIMATE STRESS
E. NOMINAL RUPTURE
STRESS
Use a scale of 1cm = 25MPa and
1cm=0.025mm/mm.
For Last name starts from A-L, the load given in
the table is added by 1.0kN except for Load OkN.
For Last Name, starts from M-Z, the load given in
the table is added by 2.5kN. Elongations do not
change.
A tension test was performed on a steel specimen
having an original diameter of 12.5 mm and gauge length
of 50 mm. Using the data listed in the table, plot the
stress-strain diagram.
Load (kN)
Elongation (mm)
0
0
11.1
0.0175
31.9
0.0600
37.8
0.1020
40.9
0.1650
43.6
0.2490
53.4
1.0160
62.3
3.0480
64.5
6.3500
62.3
8.8900
58.8
11.9380

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!
How many auxiliary views of the print?
How to draw 4/5 × 2/3 on a model
is the method of skewness used in ansys
A stationary gas-turbine power plant operates on an ideal regenerative Brayton cycle (e=100 percent) with air as the working fluid. Air enters the compressor at 95 kPa and 290 K and the turbine at 760 kPa and 1100 K. Heat is transferred to air from an external source at a rate of 75,000 kJ/s. Determine the power delivered by this plant (a) assuming constant specific heats for air at room temperature and (b) accounting for the variation of specific heats with temperature.
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
It is a good practice to include an isometric view without hidden lines as one of the views in your drawing. True? A. Good practice, same scale as principal views B. Good practice; scales can be modified C. Good practice, bust most use hidden lines D. No, isometric view should not be needed or included ANSI standards dictate the style, dimensions and arrangement of engineering working drawing layouts: A. Yes, they must be followed to ensure…… B. No companies are expected to adhere to the standards but have the latitude to the customize according to individual needs.
Provide a demonstrated drawing of the figure (construct) as well
Question 3 The Extrude Cut feature in SOLIDWORKS can be used to create both through holes (holes that go all the way through a part) and counter bore holes (holes that do not go all the way through a part), such as the holes shown in the 2-dimensional image below. True False Counterbore