A 25-mm-diameter shaft is statically torqued to 230 N. m. It is made of cast 195-T6 aluminum, with a yield strength in tension of 160 MPa and a yield strength in com- pression of 170 MPa. It is machined to final diameter. Estimate the factor of safety of the shaft.

Q: 25. ..s) Two circles, each of radius r, have their centers located at (0,2) and (0,3). Each is used…

A: As per honor code and answering guidelines I can  answer 1st question at a time.If you want other…

Q: 15 15 45 .75

A: Orthographic projection of given isometric drawing is shown below

Q: 5 400 200 A 1 120° 4 200 (mm) 350 B 2.

A: The number of I centres are given as : N=n(n-1)2N= Number of I centersn = number of links for…

Q: Consider the connection at D. What kinds of reactions can act on member AB at the connection? Click…

A: Given:Connect at DDiagram is givenTo find:kind of reactions at member AB

Q: How do you calculate the location of the centriod? What's the shape and symmetric?

A:

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to calculate third view

Q: A1A) Space is . . dimensional. O a. four O b. two O c. three O d. one

A: The space is three-dimensional because each and every point in space is  described by a linear…

Q: How we find the Metacentric Height using Metacentric Height Apparatus?

A:

Q: Y=Sinu, usxt ex डकत्र व '५

A:

Q: What is Line B?

A: Solution:

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: What is the angle between directions OA 1.6 m and OB? rOA 2 m x- 1.5 m 0.8 m utfen birini seçin a.…

A:

Q: 3. A line AB 60mm long is situated in H.P and inclined to V.P at 30 deg. The end A is 20mm in front…

A: Given Length of line AB = 60 mm Angle of inclination with vertical plane = 30o Point A is above the…

Q: Q1: Compute the new position of the square [A(11,11), B(21,11), C(21,21), D(11,21)] after its…

A: Consider the graph shown below for the given points.

Q: Creste an sometre ptora and thena caet ut l the folloing abject. The grid soacing is 10 mm.

A:

Q: The engine room of a freighter is on fre A frefghting tugboat has drawn along sde and is drecting a…

A:

Q: 0.75' C 4.5' Z 21-4 D A a 2 0.5' 2.5' B 10.5 X

A: (a) 2z ft(b) 0.5x+0.5y ft(c) -4.5x+0.75y+2.5z(d) -3.9x+y(e) 0.5x+0.5y-2z(f) 0.6x+0.25y-2.5z(g)…

Q: Cylindrical coordinates 1 ģ 1 ôT r dr Or p? og? ' ôz? ' k a ôt

A: Cylindrical Coordinates: r is in radial direction                                        z in axial…

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: Tentukan xz F.

A:

Q: Determine the center of gravity of the following shape. .06 10'-0" 6'-0" 6'-0" 20.0¹ 10'-0" 90°…

A: The center of gravity of the composite area:

Q: Question 7 of 10 The purpose of the inclining experiment is to find the: O Metacentric radius. O…

A: The purpose of inclining experiment is to establish the vertical distance of centre of gravity from…

Q: Which of the following having a direct contact with physical quantity?

A: Which of the following having direct contact with physical quaintly? Answer: b) Bourdon tube

Q: find the centride of area of ​​X and Y.

A:

Q: 1. Give the rectangular coordinates of the point C (p = 4.4, q = -115, z = 2). 2. Give the…

A:

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to find three views.

Q: 2 Draw the Vehciry triangle of body horizontal Surface and inclination angle on

A: The velocity triangle of a body on horizontal plane is -

Q: 1. Draw top, front and right side views of the bracket as shown in Fig.

A: Required Front view, Top view and Right hand side view are drawn using third angle method of…

Q: FIDENTIAL (c) A cylinder with diameter of 0.6 m is connected to a 2 m wide rectangular gate as shown…

A:

Q: Reselve the 4501b fovce intoeom ponentsacting atong members ABandAC 30 45 450

A:

Q: calcula la formula del momento en C Cx L3 L Cy B FAB L4 0₂ 0 W

A: Calculate the formula for moment at C.

Q: Find area of the shaded part using inventor

A: Find Find the area of the shaded part.

Q: So, what is the magnitud and direction from E to D. ?

A: FBE=0 FAE=288.675 lb (Compressive)

Q: he eccentricity of a conic section is 5/7. Which conic section is this? elect one: O A. Circle O B.…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   This part features…

A: The angle between the center plane of each slot is 90o. Hence, the option (d) is correct.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.