A driveshaft for a milling machine transmits15.0 hp at a speed of 240 rpm. Compute the tor-sional shear stress in the shaft if it is solid with adiameter of 1.44 in. Would the shaft be safe if thetorque is applied with shock and it is made fromSAE 4140 OQT 1300 steel?447.

Power transmitted by the driveshaft P : 15.0 hp The speed of the driveshaft N = 240 rpm The diameter…

Answered: A driveshaft for a milling machine…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
A solid 1.2 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3200 lb·in. What horsepower must be delivered to the shaft to maintain a shaft speed of 690 rpm? What is the maximum shear stress developed in the shaft?
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A driveshaft for a milling machine transmits 15.0 hp at a speed of 240 rpm. Compute the tor- sional shear stress in the shaft if it is solid with a diameter of 1.44 in. Would the shaft be safe if the torque is applied with shock and it is made from SAE 4140 OQT 1300 steel? 447.