PLEASE QUICKLY THANKS ! 3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW.P-50kW, P,=50&W, P-100kW. The allowable shear stress Id-120 MPa. LA-Lac-L-1.5m.Radius of the shaft is R=20 mm. (1)Draw the torque diagram. (2) Evaluate the strength of thisshaft. (3) Calculate the relative angle of rotation between A and D.P₂PsP₁LEGOA B C DP₁

Given Data: n=300 rpmP1=200 kWP2=50 kWP3=50 kWP4=100 kWτall=120 MPaLAB=LBC=LCD=1.5 mR=20 mm To…

3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW, P,=50&W, P-100kW. The allowable shear stress Id-120 MPa. La La La 1.5 m. Radius of the shaft is R-20 mm. (1)Draw the torque diagram. (2) Evaluate the strength of this shaft. (3) Calculate the relative angle of rotation between A and D.

3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW, P,=50&W, P-100kW. The allowable shear stress Id-120 MPa. La La La 1.5 m. Radius of the shaft is R-20 mm. (1)Draw the torque diagram. (2) Evaluate the strength of this shaft. (3) Calculate the relative angle of rotation between A and D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q/2 A/ Fill the Blanks. 1- Metals is more- -than ceramic in this property. 2- The engineering design deals with ---and - 3. Chemical reaction of a material with its environment can be considered failure by 4- prototype is- 5- Ductile fracture is characterized- -and- 6- The ---- is a material that characterize with change their shape when their temperature changes. 7- The product service life is expected to be shorter than anticipated in the design because of -----and - 8- The main characteristic of the ---- have electric properties that are combine between the conducting metallie materials and the insulating nonmetallic materials. 9- The one of the reasons for Development of existing products is---
Task 1: Produce a report by applying the concepts of engineering materials relating to a tricycle as shown in Figure 1, with the following incorporated: 3. Choose the most appropriate material from your point of view that can be used to produce the item/product with reasons discussed. Figure 1: Tricycle
I need answer within 20 minutes please please with my best wishes
n/mod/quiz/attempt.php?attempt3D2656018cmid%3D36642 NCT e-Learning Portal Courses Reports e-Services - Academic Departments - ETC - CIMS - on 17 In the classification of manufacturing process, pressing is an example of et ered O secondary machining process ed out of O primary shaping process ag question O surface finishing process O joining process stion 18 Gold chains and rings are not possible to made with hand forging operation. yet vered Select one: ked out of O True O False lag question estion 19 Identify the drilling operation in which the flat bottom drill bit is used to enlarge the existing hole. E yet wered O Type here to search 5米 ts 23 $ 6 8. V. E R Y 行 24 47
identify 3 possible places where title blocks are usually found on architectural drawings, identify at least 4 items that are commonly found in title blocks
Please don't provide handwritten solution .....
provide complete answer
Why 100% of the total material is not possible for 100% sampling
Multiple choice questions, please help thank you!! 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size clusters because of (a) their small size (b) the fewer number of atoms in them (c) surface area is smaller (d) their surface is more curved 2. Which of these characteristics would you associate with SEM: A surface imaging tool Maintained under vacuum Provides imaging and compositional data Uses a scanned electron beam All of the above 3. Secondary electrons (SE) are best described as Low energy electrons from the sample surface High energy electrons from the sample surface Low energy primary beam electrons High energy primary beam electrons 4. Atomic force microscopy (AFM) is the most widely used form of scanning probe microscopes for the characterization of nanomaterials since it require: (a) electrically conductive and optically transparent samples (b) neither electrically conductive nor optically transparent samples (c) electrically…
kinetics of particles-relative motion report
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? Z AXIS X AXIS YAXIS LEGEND A: Extruder B: Nozzle C: Printed part D: Hot plate E: Filament Table 15.2 Melting and Glass Transition Temperatures for Some of the More Common Polymeric Materials Material Polyethylene (low density) Polytetrafluoroethylene Polyethylene (high density) Polypropylene Nylon 6,6 Polyester (PET) Poly(vinyl chloride) Polystyrene Polycarbonate Glass Transition Temperature [°C (°F)] -110 (-165) -97 (-140) -90 (-130) -18 (0) 57 (135) 69 (155) 87 (190) 100 (212) 150 (300) Melting Temperature [°C (°F)] 115 (240) 327 (620) 137 (279) 175 (347) 265 (510) 265 (510) 212 (415) 240 (465) 265 (510) a. This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process b. Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process □c. You can…