Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-1bf and supports a maximum bending moment of 120 in-lbf. The driveshaft is made of steel (Sy = 50 ksi). (a) What is the safety factor against yielding using the max. shear stress criterion? Brye Zooorlst Way of 120m-1 of Shule Sponsi Safety fuctor agriax yollung using mat, Shar Stress Eriturlan. n= What is the safety factor against yielding using the max. distortion energy criterion?

Q: A large spherical tank contains gas at a pressure of 450 psi. The tank is 42 ft in diameter and is…

A:

Q: Q1/ A:1. For the triangle shown in the (fig.1) below; Determine the length of (AC); (L)

A: Given data: Length of perpendicular side BC, P = 15 cm. Length of base side AB, B = 20 cm. Part…

Q: Ten and one-half foot-pounds of work is required to compress a spring 2 inches from its natural…

A: Given data  Work = 10+1/2 (lb-ft) Initial compression = 2in  Find the work required to compress the…

Q: What are the 4 fundamental forces?

A: Given data What are the 4 fundamental forces.

Q: The engine of car has six cylinders of 82.55mm bore and 769.5mm stroke. The compression ratio is…

A:

Q: How did you get the summation of forces in each direction?

A: We can easily find the vector form of each force and then consider the sum of all the forces acting.…

Q: Q1. A conservative force is a force that the work done by it only depends on its initial and final…

A: Conservative force is the force due to which work done arise depends on initial and final positions…

Q: In Eigure 1), F-900 lb. Fy=400 lb, and F-900 lb. Figure 1 of 1 Part A Determine the magnitude of the…

A:

Q: 2.3.16. [Level 21 A Republic laser weapon targets a rade Federation battleship fleeing to space at a…

A:

Q: A 3.00 m long, 8.0 kg pole is attached to a wall by a hinge on its left side. A cable attached to…

A: To find: (a) To write the sum of forces and sum of torque equations. (b) The tension in the cable.…

Q: A. 30 m 20 m B 50 m - 40 m

A:

Q: torque (or moment) is defined as a force acting perpendicular to a moment arm about a moment center…

A: Given data T=360 lb.in

Q: -The magnitude of N2 (normal force on Surface-2) is _____N 2-The magnitude of F2 (friction force on…

A: Given:m=40 kgμ=0.5μk=0.4P=500 N

Q: A particle travels along the curve from A to B in 6 s. It takes 8 s for it to go from B to C and…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.