Water flows through a horizontal pipe at a rate of0.01 m /s. The pipe consists of two sections ofdiameters 5 cm and 2 cm with a smooth reducingsection. The pressure difference between the twopipe sections is measured by a fluid manometerthat has S=14.2. Neglecting the viscous effects,determine the differential height of fluid manometerh (m) between the two pipe sections.5 сm2 cmS Select one:а. 4.57b. 1.52С. 2.34d. 3.81e. 3.08

Answered: Image /qna-images/answer/f3b91ed1-909b-43c5-b442-1e9e2fbf4d45.jpg

Answered: that has S=14.2. Neglecting the viscous…

that has S=14.2. Neglecting the viscous effects, determine the differential height of fluid manometer h (m) between the two pipe sections.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2 in tube schedule 40 flow 24 in 4 in tube schedule 40 - 6 in water h

A: given; lets take pressure at A=PAlets take pressure at B=PB⇒diameter at A (dA)=4in=0.1016m⇒diameter…

Q: A venturi tube is used to determine the airspeed at the throat/test section. During the test, a…

Q: A fire truck supplies 190 gal/min of water to the third story of a building at B (Eigute 1) Part A…

A: this is the multiple type question . according to company policy i have answered very first question…

Q: to pump water from lower reservoir to upper reservoir, a centrifugal pump is used. if the length of…

A: Given:Suction head=3 mdelivery head=30 m

Q: Water at 10°C is flowing from point A to point B through the fabricated section shown below at the…

A: Given that: Volume flow rate = 0.37 m3/s Diameter at A = 300 mm = 0.3 m Diameter at B = 600 mm = 0.6…

Q: D;=10 cm D2=6 cm 2 h=8 cm Pc

A: Write the equation for the pressure at the manometric ends. P2=P1-ρggh+ρcgh Here, P2 is the pressure…

Q: A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the…

A: The Pressure of the water at B is 133.43 kN/m3.Explanation:Given:v1 = Velocity at location A = 1.5…

Q: In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa…

A: The pressure of first point is given as, P1=21 kPa The velocity of first point is given as, v1= 3.75…

Q: Determine the manometer reading as shown in the figure, when the velocity of fluid flowing through a…

A: Given data: The diameter of the pipe is d1=75 mm The fluid velocity is v=0.6 m/s

Q: The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: Specific gravity of oil, SGo=0.92Diameter at A, DA=400 mm=0.4 mDiameter at B, DB=600 mm= 0.6…

Q: A siphon pipe of diameter 250 mm contracts to a diameter of 100 mm over a vertical distance of 5 m…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

Q: For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

Q: 4x4 In a vertical pipe conveying oil of s= 0.7, two pressure gauges have been installed at A and B…

Q: 4. A pipe carries oil of density 800 kg/m³. At a given point (1) the pipe has a bore area of 0.005…

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: We have, Diameter, d=200 mm=0.2 m, V=3 m/s Diameter of circular plate, d1=150 mm=0.15 m (as…

Q: Turpentine is flowing at 0.63 m3/s in the fabricated tube shown below.If the pressure before the…

Q: Oil flows from a tank through a 50 mm diameter pipe. If the average velocity is 1,3 m/s, determine…

A: Diameter = 50 mm Velocity = 1.3 m/s load = 2.5 tons or 2500 kg Density = 780 kg/m3

Q: mercury is used to measure the static pressure difference between two locations A and B in a A…

A: Given:Density of mercury, ρ=13600 kg/m3g=9.81 m/s2h=150 mm or 0.15 m

Q: (a) Prove that the loss of pressure head for the viscous flow through a circular pipe is given by h.…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Flow A ↑ 100 mm S oil s= 0.82 ے وہ Flow nozzle ar B mercury S = 13.6

Q: = Q2: As shown in figure (2), when the water jet of diameter 25mm and Vj 30 m/sec., determine the…

Q: Assume the water in the first tank maintains its height and pressure. The valve is opened and after…

A: Solution: Given Data: P=200 kPaρ=1000 kg/m3D=5 cmPatm=100 kPa To Find: Mass flow rate through the…

Q: QUESTION 2 Water flows through the horizontal branching pipe shown in Figure 3. Water discharges…

Q: Water "bubbles up" above the exit of the vertical pipe attached to three horizontal pipe segments.…

Q: Consider the cone in 50 mm -50 mm 200 mm 10 mm Part A Determine the discharge of water from the…

A: Given data :- y = 40 mm Find :- Discharge = ?

Q: The figure shows a siphon which is used to draw water from a large open tank. If the absolute…

Q: Water flows through the pipe contraction shown in the figure below. For the given d=0.11 m…

Q: Q4) Water at 10°C fNows from a large reservoir to a smaller one through a 5-cm-diameter cast iron…

A: Write the given values along with suitable variables.

Q: Determine the inclination angle at point C for the water stream to reach a range of 10 m. Also…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

A: Solution:

Q: A small, high pressure water jet can be used for cutting various materials. A jet with a speed of…

A: For the solution refer below images.

Q: The specific gravity of the manometer fluid shown in the diagram is 1.07. Determine the volume…

A: To Find : The volume flow rate Given : The specific gravity of manometer fluid is

Q: For the following system, calculate the flow rate from the nozzle. Give the result Q in m3/s

Q: A large, enclosed (pressurized) cylindrical tank 3 meters high contains 2.8 meters of oil (s.g. =…

Q: The discharges from the pipe is 0.142 m3/s of water into a reservoir at a point 1.85 m below the…

A: Given:diameter at point A, da 0.254 mdiameter at discharge, d=30.5 cm or 0.305 mDischarge, Q=0.142…

Q: If the static pressure of that fluid in the pipeline is 4.3 ´ 104 Pa while its total pressure is 4.7…

Q: Water flows steadily through the system shown below. The 4-in. section leads to a throat, followed…

A: Consider the diagram shown below for the given system as shown below. From the continuity equation,

Q: Required information A jet of alcohol strikes the vertical plate as shown in figure. A force of 750N…

Q: Q4/ Gas (p = 0.0022 lb/ft) flows through duct shown in fig. At A flow rate is 60 ft /s under a…

Q: The level of mercury in the manometer has the reading shown in fig, Determine the velocity of the…

Q: 2. A 25-mm diameter shaft with density 7,870 kg/m³ is pulled through a cylindrical bore as shown.…

Question

Water flows through a horizontal pipe at a rate of
0.01 m /s. The pipe consists of two sections of
diameters 5 cm and 2 cm with a smooth reducing
section. The pressure difference between the two
pipe sections is measured by a fluid manometer
that has S=14.2. Neglecting the viscous effects,
determine the differential height of fluid manometer
h (m) between the two pipe sections.
5 сm
2 cm
S

Select one:
а. 4.57
b. 1.52
С. 2.34
d. 3.81
e. 3.08

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water enters a motor through a 500-mm-diameter pipe under a pressure of 15 kPa. It leaves through a 800-mm-diameter exhaust pipe with a pressure of 5 kPa. A vertical distance of 3 m separates the centers of the two pipes at the sections where the pressures are measured. If 600 liters of water pass the motor each second, compute the horsepower supplied to the motor.
*83. Go Two hoses are connected to the same outlet using a Y-connector, as the drawing shows. The hoses A and B have the same length, but hose B has the larger radius. Each is open to the atmosphere at the end where the water exits. Water flows through both hoses as a viscous fluid, and Poiseuille's law [Q = ™R°(P2 – P)/(8nL)] applies to each. In this law, , P, is the pressure upstream, P, is the pressure downstream, and Q is the volume flow rate. The ratio of the radius of hose B to the radius of hose A is Rg/RA = 1.50. Find the ratio of the speed of the water in hose B to the speed in hose A. Water from outlet Hose A Hose B Problem 83
Required information The rotating-cylinder viscometer in the image shears the fluid in a narrow clearance Ar as shown. Assume a linear velocity distribution in the gaps. ΦΩ Viscous fluid Solid cylinder →Ar<<
Problem 2- Determine the manometer reading as shown in the figure, when the velocity of fluid flowing through a 75mm diameter pipe is 0.6 m/sec. 25 mm Ø 75 mm Ø 75 mm Ø U Mercury -2.40 m- 750 mm
What is the pipe velocity at point 1? Given the specific gravity of pink liquid S=3.9 and height h=2.0 m. water 1 S=3.9
AVA cir Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular solid plate of diameter 150 mm is placed in the pipe to obstruct the flow. Find the loss of head due to obstruction in the pipe if C = 0.62.
b. If the pressure transducer gives a reading of 98000 Pa-a at the desired flowrate of 2.8 L/min, determine the inside diameter (mm) of the constriction segment.
Water circulates through the Venturi tube shown at 80°F. If an ideal flow is considered (without energy loss), determine the flow rate, the velocity in the pipe, and the velocity of contraction. The 9 in measurement is from center to center of the manometric tube.
Water flows through the pipe contrac- For the given 0.2-m difference in manometer level, determine the flow- rate as a function of the diameter of the small 0.2 m tion shown in Fig. h2 pipe, D. 01 m (1)
A drug is being injected into blood at a constant infusion rate of Q = 0.4mL/s from a syringe of diameter D = 4mm into a needle of diameter d = 0.2mm. The fluid viscosity is u = 0.001 Pa-s and the density is p = 1000 kg/m³. Determine the force F on the syringe plunger. Assume that the flow through the syringe and needle is laminar and that the blood pressure is P = 100 mmHg (13.33kPa). State all other assumptions used for your derivation. needle diameter d F 1 Diameter D
Following the pump, the pressure in a 6-inch inner smooth pipe conveying water is 20 pounds per square inch (psia). The water is released into a 100-foot-long open tank located from the pump. Prove that the rate of discharge of water in cubic feet per second (ft3/s) is 3.58 ft3/s.
1. A pipe 200 m long as shown in the figure tapers from 0.80 m diameter at the higher I end to 0.40 m diameter at the lower end carries 100 liters per second of oil (sp.gr.=0.85). If the pressure gauge at the lower end reads 50 KPa, determine the velocities at the two ends and the pressure at the higher end. Neglect all losses. Z₁ = 2m