The specific gravity of the manometer fluid shown in the diagram is 1.07. Determine the volume flowrate, Q, if the flow is inviscid and incompressible and the flowing liquid is (a) water, (b) gasoline, or (c) air at standard conditions

The specific gravity of the manometer fluid shown in the diagram is 1.07. Determine the volume flowrate, Q, if the flow is inviscid and incompressible and the flowing liquid is (a) water, (b) gasoline, or (c) air at standard conditions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

Q: Jet of liquid (14 mm diameter) ejections vertically into the atmosphere. The pressure inside the jet…

A: Given data Diameter (d) = 14mm = 14x10-3 m Surface tension (σ) = 8.35x10-2 N/m

Q: What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to…

Q: (d) Water flows in two different horizontal pipes having a height difference of 55cm. A U- tube…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

Q: The SG of the oil in the tank is 0.93, and a plunger with a diameter of 5 inches is being pushed…

A: V1=0.5ft/s D1=5inch D2=30mm

Q: To what height will the jet of water rise for the conditions shown in Fig. 6.40?

A: Given data: p=12 psig

Q: mercury is used to measure the static pressure difference between two locations A and B in a A…

A: Given:Density of mercury, ρ=13600 kg/m3g=9.81 m/s2h=150 mm or 0.15 m

Q: Two identical upright cylindrical tanks contains H2O, the first tank is full and the second is…

A: leth−height of both tanksso water level in first tank is h and in seocnd tank is23hLet area of…

Q: vn in the figure below has air of velocity V flowing as shown. If one of the pressure gages reads…

A: The gauge pressure at point 1 is .The gauge pressure at point 2 is .The specific weight of the air…

Q: Water flows through an orifice in the bottom of the tank shown. If the tank water away from the…

Q: Question 5: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type…

A: From these two arrangements for water as a fluid 2nd arrangement will give more accurate result as…

Q: Water "bubbles up" above the exit of the vertical pipe attached to three horizontal pipe segments.…

Q: Water flows through the pipe contraction shown in the figure below. For the given d=0.11 m…

Q: Q4) Water at 10°C fNows from a large reservoir to a smaller one through a 5-cm-diameter cast iron…

A: Write the given values along with suitable variables.

Q: Mercury has a volumetric flow rate of 30m³/s. What volume of mercury has flowed after 1 minute?

A: Write the formula for the volume flow rate of mercury. Q=Vt Here, Q is the volume flow rate of…

Q: Find the pressure head at entry of the pipe, when the pressure of flowing water is 200 N/cm2 The…

A: It is required to determine pressure head at entry of pipe in Pa

Q: The figure below shows a Venturi meter for measuring the water flow rate through a pipe. The…

A: GivenA1=0.01m2A2=0.006m2S.G=1.4h=0.8mg=9.81m/s2ρw=1000 kg/m3

Q: The reading of a pitot tube in air is 16 mm Hg at a speed of 210 km/hr. What will it read at 750…

Q: The pressure at the bottom of a tank of oil (s=0.80) is 410 kPa. Determine the equivalent head…

Q: Problem (3) Find the rate of change of h(t) (mm/s) if water is the fluid at all locations. Use V₁ =…

A: given data V1 = 7.2 m/s Q3= 1000L/min find the rate of change of h(t) in mm/sec

Q: ssure gauge column 15 cm is the speed of the water in the pipe. calculate.

Q: Q5) Using a system similar to that shown in figure, compute the required air pressure above the…

A: Given data h1 = 0.3 mh2 = 5 mWe have to find the air pressure required to cause the jet to rise to…

Q: Oil with viscosity 7.8 x 10-4 lbs and specific weight 59 flows through the funnel below. ft²…

Q: Water flows through the pipe contrac- For the given 0.2-m difference in manometer level, determine…

Q: Q1: In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline,…

A: Given data: Write the equation of continuity for the system.

Q: Water at 170 °F flows through a Venturi like the one shown in the picture. Atmospheric pressure is…

Q: What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to…

A: Given Data H=7.5 m h=2 m D=20 cm=0.2 m

Q: Consider the wind tunnel shown below. The diameter at section 1 is 0.9 m and the diameter at section…

A: Given data, WIND TUNNEL PROBLEM D1 = 0.9 m (D1 = diameter at section 1)…

Q: The pressure difference measured by a mercury oil differential manometer on the two sides of the…

Q: Consider the wind tunnel shown below. The diameter at section 1 is 0.8 m and the diameter at section…

A: Given:Diameter at section 1, d1=0.8 mDiameter at section 2, d2=0.5 mSpecific gravity of manometer…

Q: o a vertical pipeline through which water is passed, mercury speed measurement with pitot tube by…

A: Given Data Deviation in manometer column is:x=15 cm=0.15 m Density of mercury is : ρHg=13560 kg/m3…

Q: Describe the process carried on the Hall-Héroult with identifying the required processing ratio of…

A: Hall-Heroult Process

Q: When the U-tube is not rotated, the water stands in the tube as shown ( See attached figure). If the…

Q: Fluid flows through the venture tube shown below. Pressure at section 2 is equal to 101 kPa. If…

A: Given, that the pressure at the section 1 is 251 kPa and the pressure at the section 2 is 101 kPa.…

Q: Question 7 A liquid, with a density of 850 kg/m3 , is flowing downwards through a vertical pipe…

Q: What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to…

Q: Jet of liquid (14 mm diameter) ejections vertically into the atmosphere. The pressure inside the jet…

Q: Determine the absolute pressure of water at a point flowing in the pipe when the pressure head…

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

A: A venturimeter is a device which is used for the measurement of discharge of an incompressible…

Q: Determine the absolute pressure of water at a point flowing in the pipe when the pressure head…

Q: (a) A pressure gauge and manometer containing mercury are connected to the venturi meter as shown in…

A: Step 1:Step 2: Step 3: Step 4:

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

6-2
The specific gravity of the manometer fluid shown in the
diagram is 1.07. Determine the volume flowrate, Q, if the flow
is inviscid and incompressible and the flowing liquid is (a)
water, (b) gasoline, or (c) air at standard conditions
Q
0.05 m
10 mm
0.09-m
diameter
20 mm
6-5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Step 1

VIEW

Step 2: Step 2

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 14 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Write the expanded form of Darcy’s Law. Draw a tube full of sand, with piezometers, and label the components of the system.
2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.
A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the flow of a liquid of density 898 kg/m³ the reading of a mercury differential pressure gauge was 71 mm. Take the coefficient of the meter as 0.97 and the specific gravity of mercury as 13.6. Estimate the flow through the meter in m³/h.
Please solve it quickly I am at the exam
A ventury meter used to measure the liquid from the reservoir. The cross-sectional area at the inlet and throat are 4.536 x 10-3 m? and 1.134 x 103 m? with the flowrate of water is 9167 cm¾s. The level difference of mercury in manometer u tube shows the reading of 266 mm. Determine the flowrate coefficient. Given the specific gravity of mercury 13.6.
In fluid mechanics
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. (WITH FREE BODY DIAGRAM) CHOICES: A.16.5 psi B.15.5 psi C.13.5 psi D.14.4 psi
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=4.4, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 m/s 60 cm Liquid
One end of a tube of unknown radius is immersed to a depth of 15 mm in water and an air bubble is blown at the end of this tube. The maximum air pressure measured is 200 Pa. The same procedure is carried out in a liquid and the maximum air pressure recorded in 150 Pa. Determine the surface tension of the liquid. Data given: Density of water = 997 kg/m3 Density of liquid = 850 kg/m3 Density of air = 1.2 kg/m3 Surface tension of water = 72 mN/m
In a pressurized pipe, water flows at 170 C. The standard atmospheric pressure is 101.312 kPa (abs) and the local atmospheric pressure is 97.727 kPa (abs). Determine the gage pressure and its equivalent water height value that allows the cavitation to start. Show all these values schematically.
Your team is designing a chemical processing plant. You are the liquid handling and transportation specialist, and you need to transport a solvent (μ = 3.1 cP, ρ = 122k kg/m3) from a storage tank to a reaction vessel. Due to other equipment constraints, the fluid velocity must be 0.8 m/sec, and you must use stainless steel piping (ε = 0.00015 mm) with a total length (L) of 12 m. Determine the pipe inner diameter (ID) you will need to achieve a pressure drop of 0.3 kPa. Use the Moody chart.
3. A container filled with water accelerates at 20 ft/s² up a plane inclined by a = 30°. The pressure at the top of the tank, point 1, is measure at 10 psi. The length of the tank is 10 ft, and its height is 5 ft. Determine the maximum pressure in the tank. Pt. 1 ax