Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa

Q: The ultimate stress for the hitch ball is 60,000 ksi. (Capacity) The advertisement information is…

A:

Q: The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb.  Rapid cycling…

A:

Q: Please answer the below  The required formulas are attached

A: Step 1: Given Gs​=75MPa.Gb​=40MPa.db​=90mmNow let the length of the lever at B is 'l' so, the torque…

Q: The maximum value of the torsional shear stress is kpsi.

A: To find Torsional shear stress

Q: A flange coupling is to be designed, using 30 mm diameter bolts at a distance of 160 mm from the…

A:

Q: 4. As shown below, the prosthesis is made of two parts a core (G=150 ksi) and a tube (G=85 ksi). The…

A: Write the torsion equation. Here, T represents the torsional torque, J represents the polar moment…

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3°…

A: Given data:- Angle of twist =3° Length of the shaft =6 m Torque applied =14 kN-m. G = 83 kN/m2 To…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

A:

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supplies by motor is The speed of motor is The diameter of shaft 1 and 2 is The modulus of…

Q: (7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the…

A:

Q: Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A:

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supply by the motor is The speed of the motor is The diameter of shafts 1 and 2 is The…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate…

A: DefinitionS-N Diagram:The S-N diagram can be used to design components that are subject to cycle…

Q: Design a muff coupling to connect two shafts. The power to be transmitted is 27kW at a shaft speed…

A:

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.