The ultimate stress for the hitch ball is 60,000 ksi. (Capacity) The advertisement information is listed in the photos. 1) What is the maximum shear stress? (Demand) (Note you'll need to use half circle for Q) 2) What is the demand capacity stress ratio? V POWER TORQUE. PTWO011 HITCH BALL BOLA DE ENGANCHE 2" BALL DIAMETER 6000 LB. RATING 3-1/4" SHANK LENGTH PTWO011 POWER TORQUE HITCH BALL BOLA DE ENGANCHE 1" SHANK DIAMETER

Q: The round shaft shown below is subjected to an axial impact/shock direct tensile load of F = 50000…

A: It is given that the stress at groove and the hollow part is equal, thus we will first look at the…

Q: The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated.…

A: NOTCH SENSITIVITY FACTOR(q) It is defined as the susceptibility of a material to succumb to the…

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

A:

Q: spherical pressure vessel designed using steel has diameter of 36inches, shell thickness of 3/16…

A: We know that in a spherical pressure vessel the longitudinal and circumferential stresses is given…

Q: the propeller on a ship shown in figure qi is subjected to a compressive axial force f of 180 kn as…

A:

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Q: ROBLEM SET FOR SAMPAGUITA & DAISY GROUP: JAXIAL VARIABLE STRESS DESIGN BY THE LANGER-YIELD/MODIFIED…

A:

Q: Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside…

A:

Q: i kullanılmıştı ancı bölgesind

A: Given:  Power to be transmitted = 0.67 KW Rotational speed = 900 KPM Gear width = 20 mm Yield…

Q: Q6 A screw clamp as shown in the figure, exerted load (30KN), and the type of thread is (Tr.70×8.5).…

A: exerted load= 30 KNThe type of thread is  ( Tr. 70 x 8.5)Stress for nut = 60 MPaLength of the nut =…

Q: 4-T crane is used to lift a 3m x 1.2m x 200mm pre-cst panel. A preader beam is needed to ensure the…

A: Given : 3m x 1.2m x 200mm Pre cast panel Consider modulus of elasticity, E=200,000 MPa, allowable…

Q: (7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the…

A:

Q: Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a…

A:

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: The tie-rods in the press in Figure are made of the steel alloy SAE 5160 OQT 900 (E-30×106 psi).…

A:

Q: a left wing carrying single propeller engine with a mass, m= 2P00 kg. The wing has a length, L =…

A:

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: The information provided in the image includes:Maximum cylinder pressure: 3.15 N/mm²Cylinder bore:…

Q: (15) A 150mm pulley is mounted to the motor 100mm from the bearing. The motor is 20kW & rotates @…

A: Write the given data. d=150P=20 kWN=640 rpmθ=170°

Q: A circular bar is to carry a fluctuating torque from 25 to 55 N-m. Use AISI C1144 OQT 1000 for the…

A: Given: Torque, T=25 to 55 N-m Factor of safety, n=2 Stress concentration factor, kf=2.5 To find:…

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: A screw jack was used to replace the tire of a dumper. The jack had to support a load of 2000 kgf.…

A: Load W = 2000 kg-fThe parameters of the screw jack -Mean diameter d = 30 mmLength of lever L = 500…

Q: Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two…

A: Given Data The diameter of the shaft is: d=50 mm The yield strength of the shaft is: σy=440 MPa The…

Q: The composite shaft is subjected to the axial loads shown in (Figure 1). The diameters of ach…

A: given data;diameter(dAB)=19mmdiameter(dBC)=27mmdiameter(dCD)=13mmElasticity(Ecu)=126GPa=126*103MPa…

Q: PROVIDE FREE-BODY-DIAGRAM IN EVERY LETTER. Show clear hand writing and complete solution. Thank you…

A: Given: The load, P = 275 kN

Q: proper key for the joint shown in figure E rque of T= 180 N.m. The hub has length of

A: Given data shaft dia = 30 mm length of hub = 50 mm allowable compressive stress = 120 MPa Required =…

Q: The thrust bearing supports a load P = 275KN. Find a. The tensile stress in the rod b. The shearing…

A:

Q: QUA four stroke internal combustion engine has the following specifications: Brake power-7.5 kW;…

A: four stroke engine Brake power (B.P.)= 7.5 KWSpeed (N)= 1000 rpmImep (Pm)= 0.35 N/mm2max. gas…

Q: 35 mm 10 kN-m 2.36 x10° mm G, 50 GPa (1) C2 40 mm (2) 4.02 x10° mm A G2 = 25 GPa 2400 mm 3100 mm A…

A:

Q: unting for stress concentrations. calculate the safety factor for the material selected. if matrial…

A: Given-Information:- Material 4150 AnnealdF1 = 9 kNF2 = 13 kNF3 = 15 kN To-Determine:- Safety Factor…

Q: In the figure, the machine element located at the C point in the transmission system is radial and…

A: GIVEN :- Fr=500 daNFa=250daNσem=7daN/mm2N=1000 rpm   SOLUTION :- FREE BODY DIAGRAM :

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.