PROBLEM 12A 20 mm shaft is loaded as shown below (Sy = 290 MPa). Determine the location of maximum stress andcalculate the von Mises stress and factor of safety.L = 0.4 m, L₁= 0.25 m, F = 400 N, d, 100 mm, b = 20°Bearings are treated as simple supports. The tangential component of the force will produce a torqueon the shaft in addition to the bending moments.2006

Introduction: In some applications, the shaft is subjected to both bending moment and torque.…

PROBLEM 12 A 20 mm shaft is loaded as shown below (S, = 290 MPa). Determine the location of maximum stress and calculate the von Mises stress and factor of safety. L = 0.4 m, L: = 0.25 m, F = 400 N, d, = 100 mm, 6 = 20° Bearings are treated as simple supports. The tangential component of the force will produce a torque on the shaft in addition to the bending moments. Stery

PROBLEM 12 A 20 mm shaft is loaded as shown below (S, = 290 MPa). Determine the location of maximum stress and calculate the von Mises stress and factor of safety. L = 0.4 m, L: = 0.25 m, F = 400 N, d, = 100 mm, 6 = 20° Bearings are treated as simple supports. The tangential component of the force will produce a torque on the shaft in addition to the bending moments. Stery

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5: A steel cantilever shaft.The fillet is 6 mm, Sut= 560 MPa and Sy= 420 MPa. Assume the shaft surface is cold-rolled, operating temperature is 550c, reliability is 50%. Calculate the design safety factor Nfusing Good-Man theory of failure. R6 400N |$25 600N 500N 250N 200mm For the stepped rod shown which is acted upon by both a fluctuating axial force (F1) of between - 900 N and 3,600 N and a constant axial force (F2) of 2,250 N, determine (a) The factor-of-safety (Nf) using the Goodman theory. The stepped rod is made of high-strength steel, ground to the dimensions shown. The stepped rod operates at room temperature. Known that the ultimate stress 735 MPa, yield stress 500 MPa and k=1.15. d = 0.48 cm d = 0.32 cm F, F2
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
The nodal point on the shaft section is subjected to opposed shear stress, this leads to decrease in the effect of torsional shear stress which increases the fatigue life of the shaft. Select one: O True O False
Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section are constant along the bar's axis. From the fixed left end (x = 0) of the bar to the middle (x = L/2) of the bar, a lincarly varying distributed torque t, = kr, 0 < x < L/2 is applied (the unit of t, is N-m/m). At the free end (r = L) of the bar, a concentrated torque T is applied (the unit of T is N-m). According to the right-hand rule, the linearly varying distributed torque t, and the concentrated torque T both point to the r-positive direction. Find the angle of twist at the free end (x = L) (Expressing the result with G, Ip, L, T, and k). (Hint: It is easier to find the angle of twist using & = f Figure 1 shows a bar under torsion. The left end of the bar is E.) t, = kx L/2 L/2 Fig. 1. The left end (r = 0) of the bar is fixed, and the right end (r = L) of the bar is applied with a concentrated torque T. A linearly varying distributed torque t, is applied from the left end (z = 0) of…
Urgent
Which set of compatibility equations matches the following torsion members connected end-to-end in series? 30 in. O || = C a 560 8₁ a & + gap 05/0 18 in. 6 in. (2) 0 & + ₂ = 0 О ф, = фг 0 8₁ = 8₂ - 8₂ 04+₂=0 & + ₂ = constant Ta (3) 8₁ + gap = 8₂ &₁ = & + gap D. & + ₂ = constant 8 in. (2)
The spring of the check valve seen in the figure is mounted with a pre-stress of 12 mm and the diameter of the Spring Wire is 2.7 mm, the number of winding is 13, the slip module is 80800 N/mm?, the average diameter of the winding circle is 23 mm. If these conditions are taken into account, check the spring strength by finding out how much pressure the check valve will open at. Publication safe shear stress value is 185 N/mm? and 1 bar = 0.1 N / mm? will be taken. Ø10
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
The static shaft shown below is machined from aluminum 6082-T6. It is subjected to a static force of P=20 kN, T1=50 Nm, T2=50 Nm (Assume there is no buckling, Sut=240 Mpa, oy= 200 Mpa, E=70 Gpa). a) Find out the factor of safety using appropriate failure criteria. b) Determine the critical point(s) of the shaft -100 mm T2 d=20 mm P. T1