Q/ Figure below shows the load components acting on a helical gear mounted on a simply supported shaft made from steel with SAE1095 (quench at 600 °F). Bearing B takes thrust. Determine the factor of safety if the loaded shaft cross section is (20 mm), where the bending moment is dynamically repeated. Assume that K = 2.0, 1.5, and 2.0 will apply to bending, torsion, and axial loading, respectively, at the critical location..

Q/ Figure below shows the load components acting on a helical gear mounted on a simply supported shaft made from steel with SAE1095 (quench at 600 °F). Bearing B takes thrust. Determine the factor of safety if the loaded shaft cross section is (20 mm), where the bending moment is dynamically repeated. Assume that K = 2.0, 1.5, and 2.0 will apply to bending, torsion, and axial loading, respectively, at the critical location..

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.10P: Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a speed of 400 rpm and the sprocket has a pitch diameter of 6 inches. The shaft is made of ASTM-A 709 Grade 50 steel. A factor of safety of 2.5 is required. Is the design acceptable? Hint: You need to calculate torsion and bending stresses during solution.
A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20 pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.064" for good bearing life. Does the dia shown below meet the requirement? if not determine a suitable shaft diameter. 1.25-in da Gear A F₁-300- Gear B Sindia The minimum shaft diameter is in.
A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.062° for good bearing life. Check wether the shaft dia below meets the requirement. If not determine a suitable shaft diameter. 400 mm FB 350 mm 25° 300 mm FA = 11 kN• 20° 50-mm dia. Gear A, 600-mm dia. Gear B, 300-mm dia. mm. The minimum shaft diameter is determined to be
Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in
A stepped shaft has dimensions of D = 2 in., d = 1 in., and r= 0.1 in. It is machined from AISI steel of 200 Bhn hardness. The load is fully reversed axial torsion. 30 seconds of time history of the nominal torsional stress in the 1 in, section of the shaft, Tnom(t) = Tr/J, is shown (dots indicate the beginning/end of each load cycle; there are 20 cycles total in 30 seconds.). This duty cycle continues repeating. (a) Use Miner's rule to estimate the life of the shaft in cycles. (b) What is the expected life in hours. Su 0.5HB for steel. 30 20 10 -10 -20 -30 30 seconds D=2 in. d=1 in. f= 0.1 in. 200 Bhn
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F1 = 2500 lbf and F2 = 2500 lbf. The location of critical bending moment from 10.5" from point A, where bending moment is 14 750 lbf·in. Determine the minimum fatigue factor of safety based on achieving infinite life. Yield strength is 71 kpsi. If infinite life is not predicted, estimate the number of cycles to failure. Also check for yielding. Note: for the given ratio of r/d = 0.0625/1.625 = 0.04, D/d = 1.875/1.625 = 1.15 the stress concentration is given by K, =1.95. Also, use the correction of the endurance limit based on the surface factor, ka, size factor, kb, and loading factor, ke -8 in- -8 in- -8 in- 3 in -10 in- -10 in in All fillets in R. 1/4
Problem 4 The Figure shows a shaft simply supported in ball bearings at A and B, and is loaded by a force F that fluctuates between Fmax = 8 kN and F,min = 0. The shaft is made of AISI 1040 CD steel (Sut = 590 MPa) and has a fully corrected endurance limit Se 180 MPa. Estimate the life of the part. If F %3D A infinite life is predicted, calculate the factor of safety. 200 mm 200 mm Hint: The fatigue strength fraction of Sut at 103 cycles is f = 0.86. %3D 30 mm OCO.00 0.02.0,0A0 R1 R2 00.2202 AD O CI.00
Please help with all need items, analysis, element, mohir circle, wtc. Thank you.
please do it correctly