3.A large casting is suspended from two wires as shown below. The initial length ofboth wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire ismade from SAE 1020 cold drawn alloy steel and the copper wire is made from C14500copper (hard).(a) The casting is suspended such that the tensile load in each wire is identical. Whatwill be the difference in wire length between the two wires when the weaker wirereaches its yield point?(b) What mass (kg) of casting can be suspended based on the limitation in part (a)? SteelwireСopperwireCasting

Answered: Image /qna-images/answer/37466c4b-2022-46c1-83f1-4a7a391321ca.jpg

3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made from SAE 1020 cold drawn alloy steel and the copper wire is made from C14500 copper (hard). A large casting is suspended from two wires as shown below. The initial length of (a) The casting is suspended such that the tensile load in each wire is identical. What will be the difference in wire length between the two wires when the weaker wire reaches its yield point? (b) What mass (kg) of casting can be suspended based on the limitation in part (a)?

3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made from SAE 1020 cold drawn alloy steel and the copper wire is made from C14500 copper (hard). A large casting is suspended from two wires as shown below. The initial length of (a) The casting is suspended such that the tensile load in each wire is identical. What will be the difference in wire length between the two wires when the weaker wire reaches its yield point? (b) What mass (kg) of casting can be suspended based on the limitation in part (a)?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.72P: 1.72 An ice chest (see sketch) is to constructed from styrofoam . If the wall of the chest is 5-cm...

See similar textbooks

Similar questions

Using the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.
Need help with the following Question 1.Q1. A tower crane is used to lift I beams to construct skyscraper. As shown in Figure Q1 (a), the cable X is made up of two cables. The engineer whodesigning the tower crane is currently in the dilemma to determine what type of alloy is suitable for cable X with the diameter of the cable is 10 mm. The maximum allowable elongation is 0.02% which is also known as yield strain when lifting 900 kg of I beam. Given that 2 alloys are the candidates (i) Alloy WXW, E = 292 GPa and yield strength, σYS = 610 MPa and (ii) Alloy UAA, E = 169 GPa and yield strength, σYS = 414 MPa. Discuss which alloy is the most suitable.
Assume that a thin-walled cylindrical container with a radius of 65 mm and a length of 1 m is to be used to transport gas under pressure. Internal pressure is 10.13 MPa and external pressure is0.2026 MPa. Calculate the required thickness and cost in US dollars for each of the alloys in the table below. Use a safety factor of 3.5
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
In the First project: you have been asked to perform tensile testing for four different materialsand analyse the results and work on some NDT process selection:a. For the results shown in Table 1 of the tensile testing that you have performed, find thefollowing, if you know that the original length of specimen is 20.8 mm and the original diameteris 6.4 mm. Fill the calculated results in the summary table below (Table 1):1. Plot the engineering stress versus engineering strain for each material and L-D Diagram.2. Compute the modulus of elasticity, E in GPa.3. Determine the yield strength at a strain offset of 0.002.4. Determine the tensile strength in MPa.5. What is the approximate %El ductility, measured by percent elongation?6. Compute the modulus of resilience.7. Determine the fracture stress in MPa.8. Compute the final area (Af) in mm2.
PLEASE ANSWER NUMBER 5.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Assume that a thin-walled cylindrical container with a radius of 65 mm and a length of 1 m shouldused to transport gas under pressure. Internal pressure is 10.13 MPa and external pressure is0.2026 MPa. Calculate the required thickness and cost in US dollars for each of the alloys inthe table below. Use a safety factor of 3.5.
Pick the best soultion for the multiple choices. Modulus of resilience is: Slope of elastic portion of stress – strain curve Area under the elastic portion of the stress –strain curve Energy absorbed during fracture in a tension test Energy absorbed during fracture in an impact test Slope of the plastic portion of the stress- strain curve ( ) Fatigue failure occurs under the condition of: High elastic stress High corrosivity High stress fluctuations High temperature High rate of loading ( ) Creep failure of a material occurs most rapidly when the operating temperature is: Cryogenic temperature Equal to its melting point Grater than 0.4 times its melting point in K Greater than 200 oF Close to boiling point ( ) Young’s modulus of a material is indicative of its: Tensile strength Yield Strength Ductility Stiffness Corrosion Resistance…
What is the force required to a steel wire to double its length when its area of cross-section is one sq. cm and Young's modulus is 200 G Pa. As the length of the wire is doubled, the change in length is equal to its original length.
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm
(a) A circular copper ring at 24.0°C has a hole with an area of 9.97 cm2. What minimum temperature must it have so that it can be slipped onto a steel metal rod having a cross-sectional area of 10.0 cm2?_______ °C(b) Suppose the ring and the rod are heated simultaneously. What change in temperature of both will allow the ring to be slipped onto the end of the rod? (Assume no significant change in the coefficients of linear expansion over this temperature range.)________ °C
Subject: strength of materials A spherical vessel is to contain air at an average temperature of 25°C. The average mass is 250 kg. If the inside diameter is 2.5 meters, Find the required thickness of the vessel in INCHES made of steel with yield strength of 52.5 ksi. The joint efficiency is set to 75.25% and factor of safety of 5.25. Note : remember this question belongs to strength of materials Help me urgent thank you