A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 2mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Given: Fy=248MPa, Fu=400MPa Required: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.

A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 2mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Given: Fy=248MPa, Fu=400MPa Required: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter16: Engineering Drawings And Symbols

Section: Chapter Questions

Problem 50P

See similar textbooks

Related questions

Q: 60 b P P 150 100 100 100

Q: A bolted connection shown consists of an angular section L 150mmx100mm x8mm. Bolt diameter = 18mm.…

A: Answer We are given L 150 x 100 x 8 mm(A = 1894 mm2 , x = 23 mm , y = 48 mm) Bolt diameter = 18 mm…

Q: Situation 11: A single plate 180 mm x 12 mm plate is connected to a steel plate by four 22 mm…

Q: 1. Which of the following nearly gives the effective net area? O 2400 mm^2 O 2010 mm^2 1824 mm^2 O…

Q: A base plate with a dimension of 130mm x 12 mm is connected to a gusset plate with 4-16mm diameter…

Q: 10 mm 20 mm The assembly above is comprised of a 10mm-diameter steel bolt, and a 20mm-diameter,…

A: option (d) or last option is correct the explanation is given below

Q: 2. A 12mmx400mm steel plate has staggered holes arranged as shown. 60 "b" mm 12 -01 100mm Pu Pu 400…

A: a}…

Q: 1- A structural analysis was done for the steel section whose shape and characteristics are shown…

Q: Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia.) cut into the…

Q: Situation 12: A single plate 200 mm x 12 mm plate is connected to a steel plate by four 22 mm…

A: Block shear strength The Block shear failure is a limit state that occurs when tension failure…

Q: Situation 7: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (24mm dia.) cut into the…

A: Critical net area = Minimum area at particular along the section. Given data Diameter of bolt (d)…

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1= 50, y2 = y3…

Q: From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm…

Q: 2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at…

A: We are given chain pattern of boltingNet area for chain pattern of bolting is given by An = Ag -…

Q: Q1. Design the bolted connection. When a bracket is bolted to the flange of a column using a bracket…

A: Bolted bracket connection: Bracket connection of connections are mad wherever two members to be…

Q: Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard…

A: Given- diameter of bolts=20mmFu=370MpaFy=240MpaFor UNP 300B=100mtf=16mmAN=0.949m2/m

Q: The bolts used for connecting the angle shown in the figure are 22mm in diameter. The thickness of…

Q: Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the…

Q: Q3/ For the plate shown in figure below find * (a) Z A YA 7 9 X 8 5.

A: To find total area

Q: 1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and…

A: The formula to calculate the direct shear is given by, F1=Fn ...1 Here, F is given…

Q: Determine the design tensile strength of plate 150 mm x 12 mm size with holes or 16 mm diameter…

Q: A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa.…

A: Given : Allowable shearing stress, τallowable = 207 MPaDiameter of bolts, d = 20 mmDiameter of bolt…

Q: Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the…

A: Net area The net area of a member is the gross sectional area minus the holes or notches. Punching…

Q: igure is welded using a fillet weld with an electrode E70 (Fu - 485MPa) Fy - 250MPa. Use SAW…

A: (a) size of weld . Max. size of fillet weld = 16-1.6 Max. size of fillet weld = 14.4 mm…

Q: Determine the design tensile strength of plate (200 x8 mm) connected to 10-mm thick gusset using 20…

A: Given, Yield stress of the plate fy=250 N/mm2 d=20 mm Diameter of the hole do=20+1=21 mm Ultimate…

Q: Situation 3: A steel plate is 300 mm wide and 10 mm thick with 4 bolts (22mm dia.) cut into the…

Q: 2. The connections shown in the figure below consist of 10 A490 bolts and is attached to the column…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A 150x150×12 Equal Angle section is connected to a 12-mm thick plate using 3 M12 bolts. The angle…

A: Answer Design tensile capacity of the connection is minimum of the below capacity 1) Member…

Q: A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate…

Q: Calculate the value of b in mm. b. Calculate the value of the net area for tension in plates in…

Q: Problem (4): A36 steel is used for the tension member shown in Figure below. a. Determine the…

Q: sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick…

A: Given , ∝S=12x10-6/°C ES=200 GPa ∝B=20x10-6/°C EB=90 GPa Shear…

Q: repare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area…

A: Hi! Thank you for the question. We are not allowed to share excel or other files but we can help you…

Question

60 mm
b
1
110 mm
P
2
110 mm
110 mm
4.
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

16 please answer the problems, the answer is already given i just need the solution please type your answer if you can because i can't view written answers
Calculate a) the position of the centroid Answer: Xc = 0cm Yc = 4.7 cm b) the moment Ic, with respect to an axis passing through the centroid Answer: Icx = 1625 cm4 c) the moment I with respect to the axis designated in the figure. Answer Ix = 3915 cm4
500 N 200 N 200 N 200 N A E 300 225 300 225 Dimensions in mm
CALCULATE THE CENTROID OF THE GIVEN ILLUSTRATION BELOW
19:49 wamap.org Compute the coordinates of the centroid (x, y) of the area shown. Also compute the area moment of intertia about the x' and y' axes with origin at the centroid. y W a b k d b 12 mm 112 mm 11 mm 45 mm 107 mm 20 mm The coordinate of the centroid is C d h W Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 2013 Michael Swanbom cc 30 BY NC SA h mm. The y coordinate of the centroid is y = mm.
Asap please
PLease solve these two parts of the question i need them very badly
Calculate the second moment of area about the neutral X-X axis
Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces of uniform thin plate which are welded together. 285 mm 140 280 mm mm 55 mm 110 mm 165 mm -y Answers: X = i mm %3D y = i mm mm II 18 IN
1. Given: Structure shown below Find: Product of inertia with respect to x- and y-axis (Ixy) -100 mm- 20 mm mm 81 400 mm C 400 mm 20 mm T -100 mm- |- 20 mm
If the wood used for the T beam has an allowable tensile and compressive stress of allowt= 4 MPa and allow = 6 MPa respectively, determine the maximum allowable internal moment M that can be applied to the beam. 100 mm 100 mm 50 mm 50 mm 200 mm
Describe how can you measure the variation of the magnitude force that the string on the airplane when it moves along the path.