sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max

sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I the Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf=120mm d=550mm d'=80mm fc'=34MPA fy=415MPA USE NSCP 2015 mm2 A.Mu = 1400KN-m, As = mm2 B.Mu = 1700kN-m, As = mm2, As' = CS Scanned with CamScanner
| * A's O As,web As bw Steel areas: A's-2 + 14 = 308 mm² A₁=50 mm² (area of $8) Materials : C25/30 / B420C Longitudinal reinforcements A's=2 $ 14 As,web= 2 $ 12 As= 5 0 14 bw=300 mm d=670 mm d'=30 mm k₁= 0,85 k3 = 0,85 Pb=0.0205 (from table) Transverse Reinforcements $8/200 mm (2-leg stirrups) Material coefficients Ymc:1.5 (Concrete) Yms: 1,15 (Steel) Determine the reinforcement ratio and failure type of the beam As,web= 212= 226 mm² Asw=2x50=100 mm² (Total Area of two leg stirrup) A₁= 5 + 14=770 mm²
Pls answer both question, you'll get a like ty <33 Dont round off initial values, only round off in final answer ty
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Solve all the parts ( Hand written please )
Z1
Problem (4): A36 steel is used for the tension member shown in Figure below. a. Determine the nominal strength based on the gross area. b. Determine the nominal strength based on the net area. PL 300mmx17mm 150 75 75 75 75 75 125 ImmmmTmm"" mmn mm mm 50mm 100mm 100mm 50mm 19mm diameter bolts Problem (5): The tension m shown in Figur
Solve( b) part only in 2 hour plz solve this perfectly this id mecahnical emgeering question so plz don't reject it.
Determine the load capacity of the angle LRFD. USE NSCP 2015.
Ro blem 2 20" го Given Base Rate A36 (Fye36 Ksi) WI2X5 20" B= N= 20 in t= 17/2" W 12 x 50 (de12.2", bf: 8.08 in) fc: 5 ksi A= A2 Determine the max Tu that Can be applied to this base Plate ? biet: ) determine u banaal on A, (2) Chorse the Smaller af tw valus
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer