Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia.) cut into the plate as shown. Hole diameter diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 70mm, S2 = 70mm, S3 = 80mm, g1 = 70mm, g2= 70mm, g3 = 70 mm T- 1. Which of the following nearly gives the critical net area?

Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia.) cut into the plate as shown. Hole diameter diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 70mm, S2 = 70mm, S3 = 80mm, g1 = 70mm, g2= 70mm, g3 = 70 mm T- 1. Which of the following nearly gives the critical net area?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer this po, thank you so much!
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
SITUATION I A bolted tension member is shown below. Diameter of bolts are 19 mm and the plate material is A36 steel Fy = 250 MPa, Fu = 400 MPa. Diameter of hole is 2.5 mm bigger than the diameter of bolt and thickness of plate is 10 mm. 100 100 100 100 50
3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A Kolo 260 Z DX T130 130 YA |E=15KN Ans: M12
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А
The block shear strength of the tension member as shown in figure is (round off to two decimal places). Assume grade of plate Fe410. 45 mm 35 mm 50 mm 100 mm ISA 80 x 50 x 8 mm (M20 bolt of grade 4.6 is used) KN
Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 60mm, S2 = 55mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 S2 T+ H g3 DO E $3 1. Which of the following nearly gives the Allowable Strength Ta? O 652 KN O 669 KN O 674 KN O 681 KN BO CO
Solve( b) part only in 2 hour plz solve this perfectly this id mecahnical emgeering question so plz don't reject it.