1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm and f =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.)

1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm and f =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: The vertical steel bar is connected with two A307 bolts (diameter = 7/8 inch) in standard round…

A: The values given in the question are as follows: Diameter of bolt(d)=7/8 in or 0.875 in bolt grade…

Q: The L150x100x12mm, A36 steel (Fy= 248 MPa, Fu= 400 Mpa) Shown in the figure has one line of…

Q: A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate…

A: Given: 1⁄2 × 5-inch plate of A588 steel. ⇒Width, b=12in⇒Thickness, t=5 in Diameter of bolts = 5⁄8…

Q: Standard Sized Holes 0.6" ThickA36 Steel 4" Pu = 75k Pu = 75k 2.0" 2.0" 2.25" Plan View DO 7/8"…

A: Given: Pu=75 kBolt diameter=78 inFnv=68 ksiFu=58 ksi

Q: 6.8 Problem: A bracket shown in figure 6.8 carries an eccentric load of 80 kN at an eccentricity o…

Q: 1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven…

Q: The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate the…

Q: Let F = [F] N and d = 350 mm. c) Determine the moment MA of the force about bolt A. A 300 mm Upload…

Q: 200 mm W shape 75 mm 75 mm 375 mm 75 mm 75 mm 22 mm e bolt 250 mm

A: According to the interaction curve for safe value of P (Ps,Cal/Ps)<1 and, (Pt,Cal/Pt)<1

Q: The block shear strength of the tension member as shown in figure is (round off to two decimal…

A: For given tension member,grade of plate Fe410Angle specification: -ISA 80 x 50x 8 mmBolt…

Q: Question 1: Select an S shape for the tension member shown in Figure (1). The member shown will be…

A: Since the total design load (300 kips) is less than the nominal capacity (466.18 kips), the selected…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: er shown in the accompanying illustration consists of two C12 x 25s (A36 steel) connected to a 25 mm…

Q: A bolted connection shown in figure A uses the friction type connection with 22mm diameter A 325…

Q: Grade: 10.9 Included I Grade: S235 ace Class: C atio of the mean installed bolt pretension to the…

Q: For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

1. Please check the safety of bolt connection in the figure below, where F=100KN
(design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140
N/mm? and f"
=305 N/mm?. (The unit of length is mm, and ignores the weld mark
in the figure.)
F
%3D
160
b0
オ
80
4=10
|205
4=121
[8
00S

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the design capacity using ASD and NSCP specifications for the connection shown. Use A36 steel and D20 diameter bolt on an oversized hole 117 75 75 diameter. Show complete solution and round your final answer to the Pu OR nearest thousandths. PA 125 Given formula: Nominal hole diameter Due GSY: Bolt Hole diameter ØPn = ØA,F, ;ø= 0.90 dnet diameter Standard Oversized Due TRS M16 18 20 + 2mm ØP, = ØUA„Fu ;ø= 0.75 M20 22 24 + 2mm M22 24 28 + 2mm U = 1- M24 27 30 + 2mm Due to BSS ØRn = Ø[0. 60A,nyFu + U psAntFu] < ø[0.60A9„F, + UbgAntFu] ; ¢ = y -X = 14.35 mm 0.75 Slendemess Ratio < 300 ; C8x18.75 I'min For section properties I = Iox + A(y²) ly = Ioy + A(x²) A, = 3,555 mm? bf = 64.2 mm tf = 9.9 mm tw = 12.4 mm d = 203.2 mm ly = 18.31 x106 mm* Ix = 0.82 x106 mm* r = 008 75 75
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. Q # 3 15KN Rotating shaft Pillow block Metric (ISO) screw (c) Determine the stiffness of the 15 members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted. Steel 1cm Som Grey Cast Iron CLO-3, PLO-2
4. From the figure shown, an axial load P passes thru the center of gravity of the bolt group. The bolts are an A490 with threads excluded from shear plane. If this is a bearing type connection used, find the value of P. 10-22mm dia. A 490 bolts 00001