Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 60mm, S2 = 55mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm S1 S2 T+ g3 DO E $3 1. Which of the following nearly gives the Allowable Strength Ta? O 652 KN O 669 KN O 674 KN BO CO

Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 60mm, S2 = 55mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm S1 S2 T+ g3 DO E $3 1. Which of the following nearly gives the Allowable Strength Ta? O 652 KN O 669 KN O 674 KN BO CO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please provide the whole (not shortcut) and correct solution with figures. thank you Given: x =175mm Rivet Dia.,=20mm y=200mm Fy=248Mpa Fu=400 Mpa Bolt Dia.=22mm
1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm? and f" =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.) F %3D 160 b0 オ 80 4=10 |205 4=121 [8 00S
Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy= 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 52 g1 O g2 DO E $3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 O 3366 mm^2 3231 mm^2 O 3471 mm^2 A BO FO
A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 4mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Given: Fy=248MPa, Fu=400MPa Required: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.
Determine the effective net area of the L7 × 4 × 1/2 shown in the figure. Assume the holes are for 1-in Ø bolts. Use the U values given in Table 3.2. (Ans. 3.97 in^2)
Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm while holes have 21 mm diameter. Use depth 4y = 200 mm. 1. Determine the critical net width (Net Width) for the staggered bolted connection as shown in the figure. 2. Determine the value of "x" so that the net width along bolts A-B-C-D-E is equal to the net width along bolts A-B-D-E.
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556 mm², tw = 10 mm, gross depth d = 220 mm and bolts are 16-mm-diameter, with Fy=345 MPa and Fu = 450 MPa, calculate the nominal block shear strength for combined tensile rupture and shear rupture. Write your answer to the nearest whole number in kN. Consider Ubs = 1.0 T 40 mm. +* 125 mm O 4@.75 mm O O O O
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
From the figure shown, bolt diameter is 22 mm. Find: 100mm 100mm 100mm 100mm 180mm a. Shear stress due to load alone b. Most critical bolt c. Shear stress due to moment d. Maximum shear stress E92 300mm 180KM
Calculate the design strength of plates in the joint, if M16 bolts of grade 4.6 and Fe410 are used. Two plates each 16 mm thick are connected by bolts as shown in the figure. 70 mm 50 mm 300 mm