Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy= 248 MPa and Fu = 400 MPa Given: S1 = 60mm, 52-55mm, S3 = 75mm, g1 = 80mm, g2= 70mm. g3 = 70 mm $1$2 CO TA 1. Which of the following nearly gives the Design Strength Tu? BO DO 13 FO 82 83

Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy= 248 MPa and Fu = 400 MPa Given: S1 = 60mm, 52-55mm, S3 = 75mm, g1 = 80mm, g2= 70mm. g3 = 70 mm $1$2 CO TA 1. Which of the following nearly gives the Design Strength Tu? BO DO 13 FO 82 83

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556 mm², tw = 10 mm, gross depth d = 220 mm and bolts are 16-mm-diameter, with Fy=345 MPa and Fu = 450 MPa, calculate the nominal block shear strength for combined tensile rupture and shear rupture. Write your answer to the nearest whole number in kN. Consider Ubs = 1.0 T 40 mm. +* 125 mm O 4@.75 mm O O O O
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
The tension member shown in the figure is an A36 steel plate 16 mm thick. The bolts are 22 mm in diameter. Calculate the following: 50. Determine the net area (mm^2) across fracture line d-e-b-f-g. The damaged hole diameter is 4mm larger than the bolt diameter.
SITUATION I A bolted tension member is shown below. Diameter of bolts are 19 mm and the plate material is A36 steel Fy = 250 MPa, Fu = 400 MPa. Diameter of hole is 2.5 mm bigger than the diameter of bolt and thickness of plate is 10 mm. 100 100 100 100 50
3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A Kolo 260 Z DX T130 130 YA |E=15KN Ans: M12
Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 60mm, S2 = 55mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 S2 T+ H g3 DO E $3 1. Which of the following nearly gives the Allowable Strength Ta? O 652 KN O 669 KN O 674 KN O 681 KN BO CO
Subject: Steel design- Bolted Steel Connection - BOLTS SUBJECTED TO ECCENTRIC LOADS QUESTIONS: HOW MANY BOLTS (N) SHOULD APPLY FOR THIS PROBLEM IS IT 6 or 4? Please justify your answers and explain and please refer the green circle in the picture. Kindly correct what N should use if 6 or 4. Thank you
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi l) what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal places)