2. A 12mmx400mm steel plate has staggered holes arranged as shown. 60 "b" mm 12 -01 100mm Pu Pu 400 100mm 100mm 150mm a. Calculate the distance "b" so that the net area in path 1-2-3-4 is equal to the net area of path 1-2-4? b. Using the computed value of "b", solve for the critical net area. c. Calculate the ultimate safe tensile force Pu that the steel plate could carry?

2. A 12mmx400mm steel plate has staggered holes arranged as shown. 60 "b" mm 12 -01 100mm Pu Pu 400 100mm 100mm 150mm a. Calculate the distance "b" so that the net area in path 1-2-3-4 is equal to the net area of path 1-2-4? b. Using the computed value of "b", solve for the critical net area. c. Calculate the ultimate safe tensile force Pu that the steel plate could carry?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
Question 5 of 6 Fill in the blanks: Given the following: b=385mm d=550mm fc'=28MPA fy=320MPA Mu=670kN-m Determine As A. USE NSCP 2015, As = sq.mm. B. USE NSCP 2001, As = sq mm.
I the Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf=120mm d=550mm d'=80mm fc'=34MPA fy=415MPA USE NSCP 2015 mm2 A.Mu = 1400KN-m, As = mm2 B.Mu = 1700kN-m, As = mm2, As' = CS Scanned with CamScanner
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Right support: Elasticity= 374 Gpa Left support: Elasticity= 274Gpa Elongation= 9mm Answer item 1 only.
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm