Situation 7: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm S1 S2 g1 TA g2 H DO $3 1. Which of the following nearly gives the critical net area? O 2015 mm^2 2125 mm^2 O 1944 mm^2 O 1854 mm^2 BO CO

Situation 7: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm S1 S2 g1 TA g2 H DO $3 1. Which of the following nearly gives the critical net area? O 2015 mm^2 2125 mm^2 O 1944 mm^2 O 1854 mm^2 BO CO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556 mm², tw = 10 mm, gross depth d = 220 mm and bolts are 16-mm-diameter, with Fy=345 MPa and Fu = 450 MPa, calculate the nominal block shear strength for combined tensile rupture and shear rupture. Write your answer to the nearest whole number in kN. Consider Ubs = 1.0 T 40 mm. +* 125 mm O 4@.75 mm O O O O
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
SITUATION I A bolted tension member is shown below. Diameter of bolts are 19 mm and the plate material is A36 steel Fy = 250 MPa, Fu = 400 MPa. Diameter of hole is 2.5 mm bigger than the diameter of bolt and thickness of plate is 10 mm. 100 100 100 100 50
3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A Kolo 260 Z DX T130 130 YA |E=15KN Ans: M12
1
Situation 4: A steel plate is 300 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 60mm, S2 = 55mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 S2 T+ H g3 DO E $3 1. Which of the following nearly gives the Allowable Strength Ta? O 652 KN O 669 KN O 674 KN O 681 KN BO CO
Please show complete solution and explanation thank you
An A36 tension plate is 11 mm thick is given below. Bolts are 20 mm. Given that s = 60 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-c in mm2. Write your answer rounded to the nearest whole number.
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi l) what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal places)