Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 g1 TA g2 DO E $3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 O 3366 mm^2 O 3231 mm^2 O 3471 mm^2 BO CO

Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 g1 TA g2 DO E $3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 O 3366 mm^2 O 3231 mm^2 O 3471 mm^2 BO CO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard holes, as shown in the Figure below. 1= 20 mm 60 60 60 60 60 60, 60, 60, 60,60 UNP 300 F, = 370MPA F = 240MPa o o оо o o o o
An A36 (Fy=248MPA, Fu=400MPA) steel plate with thickness, t=11mm used as a tension member is connected to a gusset plate using 24mm bolts as shown. Given center to center distances: X=98mm, Y=87mm and Z=105mm. Calculate the allowable strength in KN of the tension member considering Net Section Fracture on Path DGJ? Express your answer in 2 decimal places. Steel Plate 50 Pn 50
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi k) what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places)
Determine the tensile capacity of a 200 x 100 x 12 mm angle in S275 steel assuming that the angle is connected through the longer leg by one row of M24 bolts (Fig. 3). (3 bolts in a row and p = 70 mm) M24 P Angle 200 x 100 x 12 Fig. 3 (all units in mm) * 70 O + Ö 70 *
Please provide the whole (not shortcut) and correct solution with figures. thank you Given: x =175mm Rivet Dia.,=20mm y=200mm Fy=248Mpa Fu=400 Mpa Bolt Dia.=22mm
1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm? and f" =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.) F %3D 160 b0 オ 80 4=10 |205 4=121 [8 00S
please solve and explain and neat hand writing
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy= 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 52 g1 O g2 DO E $3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 O 3366 mm^2 3231 mm^2 O 3471 mm^2 A BO FO
Box your final answers. Round off your intermediate answers to four decimal places. Express your final answers in two decimal places, thanks.
A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 4mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Given: Fy=248MPa, Fu=400MPa Required: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.
For the bolted tension member is shown in the figure. Determine the effective area, Ae. Given, x = 1.68 inch, Ag = 5.75 inch?. (4)- S/8" A325N bolts L6 x 6 x 1/2 -Tu 3" 3" 3"